Desoutter 6151653990, Manual

01/2019

8 / 56

6159932900

Issue no: 15

Original instructions.

© Copyright 2019, Ets Georges Renault 

44818 St Herblain, FR

All rights reserved. Any unauthorized use 

or copying of the contents or part thereof 

is prohibited. This applies in particular to 

trademarks, model denominations, part numbers 

and drawings. Use only authorized parts. Any 

damage or malfunction caused by the use of 

unauthorised parts is not covered by Warranty or 

Product Liability.

DECLARATION OF USE

"Class I" tool. Tool suitable for industrial 

environment only. It shall be used for tightening 

joints in wood, metal or plastic material. No other 

use will be permitted. For a reversible tool, the 

anticlockwise direction is for loosening only.

DATA

(See page 4).

Noise level: < 70 dB(A) (EN 60745).

Vibration level: < 2.5 m/s² (EN 60745).

Working temperature : 0 / +60°C.

Humidity ratio : 0 / 90%.

Declaration of noise and vibration emission

All values are current as of the date of this 

publication. For the latest information please visit 

desouttertools.com.

These declared values were obtained by 

laboratory type testing in accordance with the 

stated standards and are suitable for comparison 

with the declared values of other tools tested 

in accordance with the same standards. These 

declared values are not adequate for use in risk 

assessments and values measured in individual 

work places may be higher. The actual exposure 

values and risk of harm experienced by an 

individual user are unique and depend upon 

the way the user works, the workpiece and the 

workstation design, as well upon the exposure 

time and the physical condition of the user.

We, Desoutter, cannot be held liable for the 

consequences of using the declared values, 

instead of values reflecting the actual exposure, 

in an individual risk assessment in a work place 

situation over which we have no control. 

This tool may cause hand-arm vibration 

syndrome if its use is not adequately managed. 

An EU guide to managing hand-arm vibration 

can be found at http://www.pneurop.eu/uploads/

documents/pdf/PN3-02-NV_Declaration_info_

sheet_0111.pdf

We recommend a programme of health 

surveillance to detect early symptoms which 

may relate to noise or vibration exposure, so 

that management procedures can be modified to 

help prevent future impairment.

POWER SUPPLY

This tool has to be used with controllers of the 

Desoutter range only.

OPERATING MODE

This tool will only work with firmware 

release 4.5 and above.

The stall bar must be installed on the 

ECP tool before tightening. The reaction 

bar must be appropriate to the assembly. 

Refer to the diagram explaining how 

to use it. Be careful not to catch your 

fingers between the stall bar and the 

obstacle used for the torque control.

1.  Fit the tool with a suitable socket, then 

connect it to the power supply by means of 

the controller.

2.  Select the appropriate program on the 

controller.

3.  Hold the tool by means of the handle and 

apply to the fastener to be tightened.

In manual mode, the motor will start only when 

the trigger is operated.

When using a suspension ring, make sure that it 

is in good condition.

As the reaction force increases in 

proportion to the tightening torque, make 

sure that the tool is in perfect working 

order and the controller is programmed 

correctly, to reduce the risk of injury to 

the operator as a result of unexpected 

behaviour of the tool.

INSTRUCTIONS FOR REVERSING

(See page 6).

Never shift the gear when the machine 

is running.

●

To switch to loosening mode (1) 

(anticlockwise rotation), push the reversing 

ring (A) by hand, and turn it anticlockwise 

(C) until the red arrow is visible and the 

ring clicks into position. The reversing ring 

then remains in this position. The red arrow 

indicates the direction of rotation.

●

To switch to tightening mode (3) (clockwise 

rotation), turn the reversing ring clockwise (B) 

until the green arrow is visible and the ring 

clicks into position. The reversing ring then 

remains in this position. The green arrow 

indicates the direction of rotation.

●

If the reversing ring is placed in an 

intermediate position (2), the device is out 

of gear and the drive spindle can easily be 

turned to the desired position.