background image

Warranty

Your SWA200 subwoofer amplifier is covered by a limited warranty against 

defects in materials and workmanship for a period of (1) one year. This war

-

ranty is provided by the authorized Destination Audio dealer where the speaker 

was purchased. Warranty repair will be performed only when your purchase 

receipt is presented as proof of ownership and date of purchase. Defective 

parts will be repaired or replaced without charge by your dealer’s store or the 

location designated by your dealer authorized to service Destination Audio 

products. Charges for unauthorized service and transportation cost are not 

reimbursable under this warranty. 
This warranty becomes void if the product has been damaged by alteration, 

misuse or neglect. Destination Audio assumes no liability for property dam

-

age or any other incidental or consequential damage whatsoever which may 

result from the failure of this product. Any and all warranties of merchantability 

and fitness implied by law are limited to the duration of this express warranty. 

Some states do not allow limitations on how long an implied warranty lasts, 

so the above limitations may not apply to you. Some states do not allow the 

exclusion or limitation of incidental or consequential damages, so the above 

limitation or exclusion may not apply to you.

10

Summary of Contents for SWA200













Reviews: