background image

v.170110

  En.m5

ENGLISH

Re-packing Wheel Bearings

1. 

Loosen wheel bolts (Do not remove!).

2. 

Support trailer so the wheel is off the ground. (jack stack – floor jack – block)

3.  Remove nuts and wheel.
4.  Disassemble hub

5. 

Clean hub and pack bearings with wheel bearing grease.

6.  Re-install bearings, nut and cotter pin.

CAUTION:    

DO NOT over tighten nut. The hub must turn freely and without play.

7. 

Re-attach bolts and wheel. (Torque to 80 lbs.)

TRAILER LICENSING

The Detail K2 kit trailer MUST BE CERTIFIED after assembly by a local garage which is approved and holds a license to 

provide safety certificates for roadway vehicles.

In order to register your trailer with the Department of Motor Vehicles or Ministry of Transportation and obtain a license 

plate you will need to have either the NVIS form in Canada or the Manufacturers Certificate of Origin in the US filled 

out and signed by the dealer transferring ownership to you. This form is found in your trailer manual package. Take this 

form along with the bill of sale (cash register receipt) and safety certificate to your local Department of Motor Vehicles or 

Ministry of Transportation licensing office. Once you pay the appropriate fees you will be issued a title or registration and 

license plate to be attached to the trailer.

US Residents

To Contact National Highway Traffic Safety Administration

If you believe that your vehicle has a defect, which could cause an accident, personal injury or death, immediately inform 

the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Detail K2

If NHTSA receives similar complaints, or finds safety defects existing in a group of vehicles it may open an investigation or 

order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your 

dealer, or Detail K2.

To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in Washington, 

DC area) or write to: NHTSA, U.S. Department of Transportation, Washington, DC 20590.

Summary of Contents for MMT4X6







































Reviews: