Detection Systems DS7080iP-32 Reference Manual Download

Page: 2 / 60

Table of Contents

1.0 Specifications ............................................................ 4

1.1

Enclosure Housing ............................................................. 4

1.2

Temperature ....................................................................... 4

1.3

Power ................................................................................. 4

1.3.1

Accessory Power ...................................................... 4

1.4

Outputs .............................................................................. 4

1.5

Zones ................................................................................. 4

1.6

Keypads ............................................................................. 4

1.6.1

DS7443 Keypad ........................................................ 4

1.6.2

DS7445/DS7447 Keypads ........................................ 4

1.7

Communicator .................................................................... 4

1.8

Users ................................................................................. 4

1.9

Lightning Protection ............................................................. 4

1.10 Burglar/Fire Zone Inputs ..................................................... 4

1.11 Fire Signal Initiating Circuit (2-wire mode) ............................ 4

1.12 Standby Current Load ......................................................... 5

2.0 Enclosure Installation ............................................... 5

2.1

Install the Enclosure ............................................................ 5

2.2

Install the Control/Communicator ........................................ 5

3.0 Control Terminal Wiring ............................................ 6

4.0 System Worksheet ..................................................... 7

5.0 System Overview ....................................................... 9

6.0 Glossary ................................................................... 10

6.1

Zone Programming ........................................................... 10

6.2

Output Programming ......................................................... 11

6.3

General Control Programming ........................................... 11

6.4

Keypad Assignment Programming .................................... 12

6.5

EX8 Expansion Module Programming ............................... 12

6.6

Emergency Key Programming .......................................... 12

6.7

Custom Arming Programming ........................................... 12

6.8

Report Control Programming ............................................ 12

6.9

Day Monitor Report Control .............................................. 12

6.10 Phone Number General Control Programming .................. 13

6.11 Phone Answering Programming ........................................ 13

6.12 System Timers .................................................................. 13

6.13 Force Arming Programming .............................................. 13

6.14 Report Programming ......................................................... 13

6.15 Event History Readback Control ....................................... 14

6.16 FCC Compliance Notice ................................................... 15

6.17 FCC Phone Connection Notice To Users .......................... 15

6.18 Canadian Dept. of Communications ................................... 15

6.19 For Installations in New Zealand ....................................... 15

7.0 Operating Guide ...................................................... 16

7.1

Fire Safety ........................................................................ 16

7.1.1

If Installed in Family Residences ............................ 16

7.1.2

Having and Practicing an Escape Plan .................. 16

7.1.3

Installation Considerations ...................................... 16

7.2

Setting the Date ................................................................ 17

7.3

Setting the Time ................................................................ 17

7.4

Personal Identification Numbers ........................................ 18

7.4.1

General Information ................................................. 18

7.4.3

PIN Authority Levels ................................................ 18

7.4.2

Removing a PIN ...................................................... 18

7.5

Automatic Arming .................................................... 19

7.6

Delayed Automatic Arming ...................................... 19

7.7

Error Displays .................................................................. 20

7.8

Remote Program Dial-out and Answer .............................. 20

7.9

Zone Test .......................................................................... 21

7.10 Battery / Sounder Test ...................................................... 21

7.11 Communicator Test ........................................................... 22

7.12 Event History Readback ................................................... 22

8.0 How to Program the DS7080iP-32 .......................... 23

9.0 Programming the DS7080iP-32 .............................. 23

9.1

Address 001 - EX8 Zone Expansion Module Control ......... 24

9.2

Address 002 - General Control ......................................... 24

9.3

Address 003 - User Controls ............................................ 25

9.4

Address 004 - Programmer and Master Codes ................. 25

9.5

Address 005 - Cross-Zoning ............................................ 25

9.6

Address 006 - Trip window ................................................ 25

9.7

Address 007 - Keypad Assignment ................................... 26

9.8

Address 008 - Language and Arming Controls .................. 26

9.9

Address 009 - Output Programming .................................. 26

9.10 Address 010 - Time Delays ............................................... 27

9.11 Address 011 - Report Controls ......................................... 27

9.12 Address 012 - Phone Controls .......................................... 28

9.13 Address 013 - Partition 1 Account Codes .......................... 28

9.14 Address 014 - Partition 2 Account Codes .......................... 28

9.15 Address 015 - Phone # 1 Format ...................................... 29

9.16 Address 016 - Phone # 2 Format ...................................... 29

9.17 Address 017 - 022 - Phone Numbers ................................ 30

9.18 Address 023 - Dial Attempts ............................................. 30

9.19 Address 024 - Auto Test / Remote Programmer Call-Out Day

9.20 Address 025 - Auto Test / Remote Programmer Call-Out Time

9.21 Address 026 - AC Report Delay ........................................ 31

9.22 Address 027 - History Controls ......................................... 31

9.23 Address 028 - Special Keys .............................................. 31

9.24 Addess 029 - Keypad Reports .......................................... 32

9.25 Address 030, 031, 032, 033 - Zone Type ........................... 32

9.26 Address 034, 035, 036, 037 - Zone Action ........................ 34

9.27 Address 038, 039, 040, 041 - Output Type ........................ 34

9.28 Address 042, 043, 044, 045 - Zone Bypass ...................... 35

9.29 Address 046, 047, 048, 049 - Custom Arming ................... 35

9.30 Address 050, 051, 052, 053 - Zone Partition Assignment .. 35

9.31 Addresses 054, 055, 056, 057 - Zone Alarm Reports ........ 36

9.32 Addresses 058, 059, 060, 061 - Zone Restoral Reports .... 36

9.33 Addresses 062, 063, 064, 065 - Zone Trouble Reports ...... 37

9.34 Addresses 066, 067, 068, 069 - Trouble

Restoral Reports .............................................................. 37

9.35 Addresses 070, 071, 072, 073 - Zone Bypass Reports .. 37

9.36 Addresses 074, 075, 076, 077 - Bypass

Restoral Reports .............................................................. 37

9.37 Address 078 - Open/Close Reports ................................ 38

9.38 Address 079 - AC/Battery Reports .................................. 38

9.39 Address 080 - Remote/Local Programming Reports ...... 38

9.40 Address 081 - Exit Error, Recent Closing, System Trouble,

System Trouble Restoral Reports ..................................... 38

9.41 Address 082 - Test Reports ............................................. 38

9.42 Address 083 - 116 - Alpha Labels ................................... 39

9.43 Address 117 - Point Expansion Module Missing Report . 39

9.44 Address 118 - Point Expansion Module Missing Restoral

Report ............................................................................... 39

9.45 Address 119 - Point Expansion Module Tamper Report .. 40

9.46 Address 120 - Point Expansion Module Tamper Restoral

Report ............................................................................... 40

Summary of Contents for DS7080iP-32
























































Search results

Summary of Contents for DS7080iP-32

Reviews:

Related manuals for DS7080iP-32

Brands by name

Popular brands

Detection Systems DS7080iP-32, Reference Manual

Search results

Summary of Contents for DS7080iP-32

Reviews:

Related manuals for DS7080iP-32

Brands by name

Popular brands