Detection Systems DS7080iP-32 Reference Manual Download

Page: 45 / 60

10.3.5 Central Station Burglary Alarm

The control must be installed in accordance with UL Standards
UL611 and UL681 for all grades of service.

A. Grades AA and A Installations using the Applied Spectrum

PAL200 and the DACT

Required Accessories:

• The control must be installed in a Detection Systems’ model

AE7080CC enclosure with a cover actuated tamper switch
installed.

• The Applied Spectrum PAL200.

• The Spectrum PAL200 must be installed within 3 feet of the control

and the wiring to the control must be in conduit.

• The Applied Spectrum PAL200 inputs should be connected to

the alarm outputs (the active alarm sounder output may be used).

1. Report Programming:

• Programming shall be enabled to allow all alarm signals to be

transmitted via the DACT and PAL200.

• Burglar Zone Reports are not required since the alarms are

transmitted over the PAL200.

• Low Battery Report (Program Address 079, digits 1 & 2) must be

programmed.

• AC Failure Report (Program Address 079, digits 5 & 6) must be

programmed.

• Open Report (Program Addresses 011, digit 1, and 078, digits 1

& 2) must be programmed.

• Close Report (Program Addresses 011, digit 1, and 078, digits 3

& 4) must be programmed.

• 24-Hour Check-In Reports (Program Addresses 082, digits 1-4,

024 and 025, all digits) must be programmed.

2. Timer Programming:

• Entry, Exit Delay Times (Program Address 010, digits 1-9) must

be programmed for not longer than 60 seconds.

3. General Control Programming:

• Program Address 002, digit 2, must be programmed for Closing

Ringback and digit 3 must be programmed for no swinger shunts.

• Program Address 002, Force Arming Limit, must be programmed

as: digits 8 & 9 = 0.

• Program Address 008, digit 2, must be programmed for the

Commercial mode (digit 2 = 0).

4. Zone Programming:

• The Burglar alarm output signal (whether pulsed or steady) must

be different from the Fire alarm signal.

5. Alarm Output Programming:

• Alarm Output, Program Address 009, digit 1 must be programmed

as *0 (A).

B. Grade B Installations using Digital Alarm Communicator

Transmitter with local bell

Required Accessories:

• The control must be installed in a Detection Systems’ model

AE7080CC enclosure with a cover actuated tamper switch
installed.

• The Ademco Model AB-12 bell/housing (see Section 10.4).

1. Report Programming:

• Burglar Zone Reports must be programmed for those zones used.

• Low Battery Report (Program Address 079, digits 1 & 2) must be

programmed.

• AC Failure Report (Program Address 079, digits 5 & 6) must be

programmed.

• Open Report (Program Addresses 011, digit 1, and 078, digits 1

& 2) must be programmed.

• Close Report (Program Addresses 011, digit 1, and 078, digits 3

& 4) must be programmed.

• 24-Hour Check-In Reports (Program Addresses 082, digits 1-4,

024 and 025, all digits) must be programmed.

2. Timer Programming:

• Bell Cutoff Times (Program Address 010, digits 10-15) must be

programmed for not less than 15 minutes.

• Entry, Exit Delay Times (Program Address 010, digits 1-9) must

be programmed for not longer than 60 seconds.

3. General Control Programming:

• Program Address 002, digit 2, must be programmed for Closing

Ringback and digit 3 must be programmed for no swinger shunts.

• Program Address 002, Force Arming Limit, must be programmed

as: digits 8 & 9 = 0.

• Program Address 008, digit 2, must be programmed for the

Commercial mode (digit 2 = 0).

4. Zone Programming:

• The Burglar alarm output signal (whether pulsed or steady) must

be different from the Fire alarm signal.

5. Alarm Output Programming:

• Alarm Output, Program Address 009, digit 1 must be programmed

as *0 (A).

C. Grade C Installations using Digital Alarm Communicator

Transmitter only

Required Accessories:

• The control must be installed in a Detection Systems’ model

AE7080CC enclosure with a cover actuated tamper switch
installed.

1. Report Programming:

• Burglar Zone Reports must be programmed for those zones used.

• Low Battery Report (Program Address 079, digits 1 & 2) must be

programmed.

• AC Failure Report (Program Address 079, digits 5 & 6) must be

programmed.

• Open Report (Program Addresses 011, digit 1, and 078, digits 1

& 2) must be programmed.

• Close Report (Program Addresses 011, digit 1, and 078, digits 3

& 4) must be programmed.

• 24-Hour Check-In Reports (Program Addresses 082, digits 1-4,

024 and 025, all digits) must be programmed.

2. Timer Programming:

• Entry, Exit Delay Times (Program Address 010, digits 1-9) must

be programmed for not longer than 60 seconds.

3. General Control Programming:

• Program Address 002, digit 2, must be programmed for Closing

Ringback and digit 3 must be programmed for no swinger shunts.

• Program Address 002, Force Arming Limit, must be programmed

as: digits 8 & 9 = 0.

Summary of Contents for DS7080iP-32
























































Search results

Summary of Contents for DS7080iP-32

Reviews:

Related manuals for DS7080iP-32

Brands by name

Popular brands

Detection Systems DS7080iP-32, Reference Manual

Search results

Summary of Contents for DS7080iP-32

Reviews:

Related manuals for DS7080iP-32

Brands by name

Popular brands