manualshive.com logo in svg

Detection Systems DS7080iP-32, Reference Manual

The Detection Systems DS7080iP-32 is a cutting-edge security product suitable for both residential and commercial use. To fully understand and utilize its features, make sure to access the detailed Reference Manual available for free download at 88.208.23.73:8080. This comprehensive manual will be your go-to resource for maximizing the potential of this exceptional product.

Share
Download
background image

 Page 54     P/N 39818D                             Copyright © 2001 Detection Systems, Inc.                             DS7080iP-32 Reference Guide

13.0

Programming Addresses

50/60 Hz .................................................................................................. 002
AC Failure Report ................................................................................... 079
AC Failure Report Delay ......................................................................... 026
AC Failure Restoral ................................................................................. 079
Alarm Bell Cutoff ..................................................................................... 010
Alarm Output ........................................................................................... 009
Alarm Output on Manual Arming ............................................................ 003
Allow All Arming Levels ........................................................................... 002
Alpha for Zone 1-8 ........................................................................... 085-092
Alpha for Zone 9-16 ......................................................................... 093-100
Alpha for Zone 17-24 ....................................................................... 101-108
Alpha for Zone 25-32 ....................................................................... 109-116
Arming Mode ........................................................................................... 008
Arming Warning Control .......................................................................... 003
Automatic Comm. Test Report ................................................................ 082
Automatic Comm. Test  Report Call-Out Day .......................................... 024
Automatic Comm. Test Report Call-Out Time ......................................... 025
Burglary Bell Cutoff ................................................................................. 010
Callback .................................................................................................. 012
Close Report ........................................................................................... 078
Close Report Control .............................................................................. 011
Closing Ringback .................................................................................... 002
Cross-zoning Control .............................................................................. 005
Cross-zoning Trip Window Time .............................................................. 006
Custom Arming Zones 1-8 ...................................................................... 046
Custom Arming Zones 9-16 .................................................................... 047
Custom Arming Zones 17-24 .................................................................. 048
Custom Arming Zones 25-32 .................................................................. 049
Day Monitor Trouble Report Control ........................................................ 011
Defaulting the System ............................................................................. 124
Dial Attempts ........................................................................................... 023
Dialer Delay ............................................................................................. 012
Duress Report ......................................................................................... 078
Emergency Key Control .......................................................................... 028
Emergency Key Report ........................................................................... 029
Entry Delay Time 1 .................................................................................. 010
Entry Delay Time 2 .................................................................................. 010
Exit Delay Time ....................................................................................... 010
Exit Error Report ..................................................................................... 081
Expansion Module .................................................................................. 001
Expansion Module Missing Report ......................................................... 117
Expansion Module Missing Restoral ....................................................... 118
Expansion Module Tamper Report .......................................................... 119
Expansion Module Tamper Restoral ....................................................... 120
Expansion Module Fault Report .............................................................. 121
Expansion Module Fault Restoral ........................................................... 122
Fire Bell Cutoff ........................................................................................ 010
Fire Key Control ...................................................................................... 028
Fire Key Report ....................................................................................... 029
First Open After Alarm Report ................................................................ 078
Force Arming Limit .................................................................................. 002
General Control ....................................................................................... 002
Ground Start ........................................................................................... 009
History Event Control .............................................................................. 027
Keypad Assignment ................................................................................ 007
Keypad Audible During Exit .................................................................... 003
Keypad Control ....................................................................................... 008
Keypad Emergency Alarm Report .......................................................... 029
Keypad Fire Alarm Report ...................................................................... 029
Keypad Fire Restoral .............................................................................. 029
Keypad Language ................................................................................... 008
Keypad Panic Report .............................................................................. 029
Keyswitch Tamper Report ....................................................................... 029
Language Controls .................................................................................. 008
Local Program Successful Report .......................................................... 080
Local Program Unsuccessful Report ...................................................... 080
Low Battery Report ................................................................................. 079
Low Battery Restoral .............................................................................. 079
Manual Comm. Test Report ..................................................................... 082
Master Code ........................................................................................... 004
Octal Relay Control ................................................................................. 123
Octal Relay Missing Report .................................................................... 123
Octal Relay Missing Restoral .................................................................. 123
Open Report ........................................................................................... 078
Open Report Control ............................................................................... 011
Panic Key Control ................................................................................... 028
Panic Key Report .................................................................................... 029
Partial Close Report ................................................................................ 078
Partition 1 Account Codes ...................................................................... 013

Partition 1 Alpha ..................................................................................... 083
Partition 2 Account Codes ...................................................................... 014
Partition 2 Alpha ..................................................................................... 084
Partitioning .............................................................................................. 002
Phone Answer Rings - Armed ................................................................. 012
Phone Answer Rings - Disarmed ............................................................ 012
Phone Controls ....................................................................................... 012
Phone #1 ................................................................................................. 017
Phone #1 Format .................................................................................... 015
Phone #2 ................................................................................................. 019
Phone #2 Format .................................................................................... 016
Phone #3 ................................................................................................. 021
PIN Length .............................................................................................. 003
Programmable Output 1 .......................................................................... 009
Programmable Output 2 .......................................................................... 009
Programmer's Code ................................................................................ 004
Recent Closing Report ............................................................................ 081
Remote Program Successful Report ...................................................... 080
Remote Program Unsuccessful Report .................................................. 080
Remote Programmer Call-Out Day ......................................................... 024
Remote Programmer Call-Out Time ........................................................ 025
Remote Programmer Phone ................................................................... 021
Siren on Comm. Failure .......................................................................... 002
System in Test Report ............................................................................. 082
System in Test Restoral .......................................................................... 082
System Trouble Report ........................................................................... 081
System Trouble Restoral ......................................................................... 081
Swinger Shunt ......................................................................................... 002
Test Report ............................................................................................. 082
Tone/Pulse .............................................................................................. 012
Trip Window ............................................................................................. 006
Trouble Zone Mode ................................................................................. 003
WDSRP Baud Rate ................................................................................. 012
Zone Action Zones 1-8 ............................................................................ 034
Zone Action Zones 9-16 .......................................................................... 035
Zone Action Zones 17-24 ........................................................................ 036
Zone Action Zones 25-32 ........................................................................ 037
Zone Alarm Report Zones 1-8 ................................................................ 054
Zone Alarm Report Zones 9-16 .............................................................. 055
Zone Alarm Report Zones 17-24 ............................................................ 056
Zone Alarm Report Zones 25-32 ............................................................ 057
Zone Alarm Restoral Zones 1-8 .............................................................. 058
Zone Alarm Restoral Zones 9-16 ............................................................ 059
Zone Alarm Restoral Zones 17-24 .......................................................... 060
Zone Alarm Restoral Zones 25-32 .......................................................... 061
Zone Bypass Zones 1-8 .......................................................................... 042
Zone Bypass Zones 9-16 ........................................................................ 043
Zone Bypass Zones 17-24 ...................................................................... 044
Zone Bypass Zones 25-32 ...................................................................... 045
Zone Bypass Report Zones 1-8 .............................................................. 070
Zone Bypass Report Zones 9-16 ............................................................ 071
Zone Bypass Report Zones 17-24 .......................................................... 072
Zone Bypass Report Zones 25-32 .......................................................... 073
Zone Bypass Restoral Report Zones 1-8 ............................................... 074
Zone Bypass Restoral Report Zones 9-16 ............................................. 075
Zone Bypass Restoral Report Zones 17-24 ........................................... 076
Zone Bypass Restoral Report Zones 25-32 ........................................... 077
Zone Output Zones 1-8 ........................................................................... 038
Zone Output Zones 9-16 ......................................................................... 039
Zone Output Zones 17-24 ....................................................................... 040
Zone Output Zones 25-32 ....................................................................... 041
Zone Partitioning Assignment Zones 1-8 ................................................ 050
Zone Partitioning Assignment Zones 9-16 .............................................. 051
Zone Partitioning Assignment Zones 17-24 ............................................ 052
Zone Partitioning Assignment Zones 25-32 ............................................ 053
Zone Restore Control .............................................................................. 002
Zone Trouble Report Zones 1-8 .............................................................. 062
Zone Trouble Report Zones 9-16 ............................................................ 063
Zone Trouble Report Zones 17-24 .......................................................... 064
Zone Trouble Report Zones 25-32 .......................................................... 065
Zone Trouble Restoral Zones 1-8 ............................................................ 066
Zone Trouble Restoral Zones 9-16 .......................................................... 067
Zone Trouble Restoral Zones 17-24 ........................................................ 068
Zone Trouble Restoral Zones 25-32 ........................................................ 069
Zone Type Zones 1-8 .............................................................................. 030
Zone Type Zones 9-16 ............................................................................ 031
Zone Type Zones 17-24 .......................................................................... 032
Zone Type Zones 25-32 .......................................................................... 033

Address

Address

Summary of Contents for DS7080iP-32





























































Reviews:

No comments

Related manuals for DS7080iP-32

HAFURY M20 Quick Start Manual preview
M20
Brand: HAFURY Pages: 60
Panasonic EB-3901 User Manual preview
EB-3901
Brand: Panasonic Pages: 83
Panasonic KX-UT123 Admin Manual preview
KX-UT123
Brand: Panasonic Pages: 5
Panasonic KX-UT123 Administrator'S Manual preview
KX-UT123
Brand: Panasonic Pages: 312
Panasonic Section 700 Technical Manual preview
Section 700
Brand: Panasonic Pages: 311
Samsung GT-P3100 Servise Manual preview
GT-P3100
Brand: Samsung Pages: 78
Fanvil X3S Basic Manual preview
X3S Basic
Brand: Fanvil Pages: 16
ASCOM Ascotel 200 Manual preview
Ascotel 200
Brand: ASCOM Pages: 46
Uniden VP300 Owner'S Manual preview
VP300
Brand: Uniden Pages: 141
E-TEN glofiish DX900 Technical & Service Manual preview
glofiish DX900
Brand: E-TEN Pages: 30
Obihai OBi1062 Quick Start Manual preview
OBi1062
Brand: Obihai Pages: 3
Caliber HFB 400 User Manual preview
HFB 400
Brand: Caliber Pages: 10
Alcatel OT-S319 User Manual preview
OT-S319
Brand: Alcatel Pages: 36
HTC HTC Incredible S User Manual preview
HTC Incredible S
Brand: HTC Pages: 78
HTC Touch NIKI100 User Manual preview
Touch NIKI100
Brand: HTC Pages: 240
HTC Converce Service Manual preview
Converce
Brand: HTC Pages: 78
IPRO i9 Manual preview
i9
Brand: IPRO Pages: 66
BlueParrott Xpressway II User Manual preview
Xpressway II
Brand: BlueParrott Pages: 16

Brands by name

Popular brands

Load more brands