background image

PAGE 2

PAGE 11

This product is intended for indoor use only.

Always operate the product from a power source of the same voltage, frequency and rating 
as indicated on the product identification plate.

To reduce the risk of electric shock, do not use this fan with any solid state speed control 
device.

This appliance is not intended for use by persons (including children) with reduced physical, 
sensory or mental capabilities, or lack of experience and knowledge, unless they have been 
given supervision or instruction concerning use of the appliance by a person responsible for 
their safety.

Do not insert fingers or any other foreign object through the front and rear guards into the 
blade.

Close supervision is necessary when any product is used by or near children or infirm 
persons. Do not allow children to use it as a toy.

Do not operate any product with a damaged cord or plug, after the product malfunctions, is 
dropped or appears damaged in any way. Return the complete product to the place of 
purchase for inspection, repair, or replacement.

To reduce the risk of electric shock, do not immerse or expose the product or flexible cord to 
rain,moisture, or any liquid.

This product should not be used in the immediate vicinity of water, such as sinks, bathtubs, 
washbowls, swimming pool, etc. where the likelihood of immersion or splashing could 
occur.

Switch off and unplug from outlet when not in use, before assembling or disassembling 
parts, and before cleaning. Fully assemble the fan before switching on.

Avoid contact with moving parts. Do not insert any object through the grill when the fan is 
operating.

Do not cover the grill, or operate in close proximity to curtains, etc.

Always disconnect the fan when moving it from one location to another.

The use of attachments or accessories not recommended or sold by the product distributor 
may cause personal or property hazards or injuries.

SAFETY INSTRUCTIONS 

Summary of Contents for DFS75







Reviews: