Devantech ETH008 Technical Documentation Manual Download | Manualshive

Page: 5 / 17

background image

Accessing the ETH8020 from your browser

Having plugged in your 12vdc power supply and Ethernet connection the board will power up and request an IP
address from the DHCP server, if no server is present then the board will default to IP address 192.168.0.200.

Now please start up your web browser and type http

://ETH8020

into the address bar, please note this only works in

windows. You will be prompted for a password as shown below:

The default login is:

Username: admin

Password: password

The ability to change these

settings is shown in the

configuration section

You should now see the following web page:

This web page will allow you to switch the relays on and off by clicking the relay buttons (the red/gray circles). It also
contains a links to this technical documentation page, the network configuration and mapped inputs.

© Devantech Ltd 02/07/19

ETH8020 Documentation

5/17

«
...
3
4
5
6
7
...
»

Summary of Contents for ETH008


















Reviews:

No comments

Related manuals for ETH008

Brand: Woodward Pages: 119

Brand: Eaton Pages: 3

Brand: finder Pages: 2

Brand: Hitachi Pages: 36

LD Relays (ALD)

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 5

Brand: Littlefuse Pages: 92

Brand: Tri-M Systems Pages: 20

Brand: F&F Pages: 4

Brand: Eaton Pages: 33

Brand: ABB Pages: 11

ESR5-NZ-21-24VAC-DC

Brand: Eaton Pages: 19

Brand: GE Pages: 56

Brand: Thytronic Pages: 146

Brand: TE Connectivity Pages: 2

Brand: axing Pages: 4

Brand: NR Electric Pages: 480

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands