Page 6 SB-2-611
ENGLISH
2/03
©Copyright 2003,
Printed in U.S.A.
WARRANTY
This product is covered by DeVilbiss' 1 Year Limited Warranty. See SB-1-000 which is available upon request.
DeVILBISS WORLDWIDE SALES AND SERVICE LISTING - www.devilbiss.com
AUTOMOTIVE REFINISHING
DeVilbiss has authorized distributors throughout the world. For equipment, parts and service, check the Yellow Pages
under "Automobile Body Shop Equipment and Supplies".
FOR TECHNICAL ASSISTANCE, CALL TOLL FREE
1-800-445-3988 (U.S.A. ONLY). FOR LOCAL CALLS, SEE LISTING BELOW.
U.S. Customer Service Office
Address
Telephone No.
MAUMEE, OH 43537
1724 Indian Wood Circle
(419) 891-8100
Toll Free Fax No. 1-800-445-6643
HARG-510 Air Regulator
Use to maintain nearly constant outlet
pressure despite changes in inlet
pressure and downstream flow.
HAV-500 OR HAV-501
Adjusting Valve
(HAV-501 SHOWN)
HAV-500 does not have
pressure gauge. Use to con-
trol air usage at gun.
HAF-507
Whirlwind™
In-Line Air Filter
Removes water, oil, and
debris from the air line.
ACCESSORIES
MSP-524
Twin Cartridge,
Paint Spray
Respirator
NIOSH-Certified (TC84A-
1623) for respiratory
protection in atmos-
pheres not immediately
dangerous to life.
FUN-5033-V
Air Cap Test Kit
The purpose of this test kit is
to measure air cap atomizing
air pressure at the center air
port of the air cap. Used to
confirm code compliance and
as a daily quality control
measure.
Spray Gun
Lube
SSL-10
(2 oz.
bottle)
Compatible with all
paint materials; con-
tains no silicone or
petroleum distillates
to contami
nate paint.
MSDS available upon
request.
Automotive Quick
Connects
For HVLP Guns (Air)
High Flow Type.
HC-4720 Coupler
1/4" NPT(F)
HC-4719 Coupler
1/4" NPT(M) /NPS(M)
192212 Professional Spray Gun
Cleaning Kit
Contains six precision tools designed to effec-
tively clean all DeVilbiss, Binks, Finishline and
other brand spray guns.
192218 Scrubs
®
Hand Cleaner Towels
Scrubs
®
are a premoistened hand cleaner
towel for painters, body men and mechanics
that go where you go and no water is needed.
192219 Gun Holder
Gun holder made to
hold guns with gravity
feed cups.
TROUBLESHOOTING (Continued)
CONDITION
CAUSE
CORRECTION
Runs and sags
Thin, sandy coarse finish drying
before it flows out
Thick, dimpled finish "orange
peel"
Too much material flow.
Material too thin.
Gun tilted on an angle, or gun motion too slow.
Gun too far from surface.
Too much air pressure.
Improper thinner being used.
Gun too close to surface.
Air pressure too low.
Improper thinner being used.
Material not properly mixed.
Surface rough, oily, dirty.
Adjust gun or reduce fluid flow.
Mix properly or apply light coats.
Hold gun at right angle to work and adapt to
proper gun technique.
Check distance. Normally approximately 8".
Reduce air pressure and check spray pattern.
Follow paint manufacturer's mixing instructions.
Check distance. Normally approximately 8".
Too much material coarsely atomized.
Increase air pressure or reduce fluid flow.
Follow paint manufacturer's mixing instructions.
Follow paint manufacturer's mixing instructions.
Properly clean and prepare.
HC-1166 Stem
1/4" NPT(M)
HC-4419 Stem
1/4" NPT(F)
