background image

EN

SB-2-301-V  (7/2014)

6 / 8

ACCESSORIES

Contains all necessary 

tip, hose and nut sizes 

used on or with gun.

WR-103 Wrench

These brushes are helpful 

in cleaning threads and 

recesses of gun body.

42884-214-K5 3/8"

42884-215-K10 5/8"

Cleaning Brushes

HD-503  

SolventSaver™ 

Hose/Gun

Cleaner

2 Qt. & 2-1/2 Gal hose/gun 

cleaner used to clean the 

inside of hose, fluid pas-

sageways of gun & other 

paint equipment. 

183GZ-5200  

SolventSaver ™ 

Hose/Gun

Cleaners

2 Gallon galvanized tank 

used to clean the inside 

of hose and material pas-

sages of the gun.

JGA-156-K10 

Spring Clip

Joins any single piece 

DeVilbiss air cap with 

latest version MBC-368 

or MSA-1 retaining ring. 

Helps prevent parts loss 

and provides easier as-

sembly.

Compatible with all paint 

materials: contains no 

silicone or petroleum 

distillates to contaminate 

paint.  MSDA sheet avail-

able upon request.

Spray Gun Lube

SSL-10  

(2 oz. bottle) 

HAV-500 OR

HAV-501

Adjusting Valve

(HAV-501 SHOWN)

HAV-500 does not have 

pressure gage.  Use to 

control air usage at gun.

VS-531  

Low Pressure 

Strainers

The VS-531 Low Pres-

sure Fluid Strainer pro-

vides a final filter for 

trapping foreign particles 

in the paint supply.

MB-135-K9 

Leather 

Packings

Optional packings used 

commonly with abrasive 

materials.  Use (3) in place 

of A-23 packing.

Enables user to control  

and reduce air usage 

at the gun. Ideal for low  

pressure spraying.

P-H-5516 Air  

Adjusting Valve

HAF-507 

Whirlwind™

In-Line Air Filter

Removes water, oil, and 

debris from the air line.

Quick Disconnect Approved for 

HVLP Guns (Air)

  High Flow Ball and Ring Type

HC-4419 1/4" 

NPS(F)

HC-4699

1/4" NPT(M)

HC-1166

1/4" NPT(M)

HC-4700

1/4" NPT(F)

Provides greater 

degree of con-

trol over cup fluid  

pressure.

KB-555 (Aluminum) & 

KB-545-SS (S/S) 2 qt. Pressure 

Feed Cup With Regulator

TGC-545 (Aluminum) TLC-555 

(Non-stick coating)

TSC-595 S.S. 1 Qt. Drip-Free 

Suction Cup

Cup has a unique, two position 

valve which permits selection of 

either a drip-free or conventional 

open vent mode.

NIOSH-Certified, for  

respiratory protection  

in atmospheres not  

immediately dangerous 

to life.

Millennium 3000

 

 

Twin Cartridge  

Paint Spray Respirator

HARG-510  Air

Regulator

Use to maintain nearly 

constant outlet pres-

sure despite changes 

in inlet pressure and 

downstream flow.

Scrubs® are a pre-

moistened hand clean-

er towel for painters.  

No water is needed.

29-3100 Scrubs

®

 

Hand Cleaner Towels

Summary of Contents for MBC-510









Reviews: