background image

EN

SB-2-301-V  (7/2014)

8 / 8

Finishing Brands reserves the right to modify equipment specifications without 

 

prior notice. DeVilbiss, Ransburg, BGK, and Binks are registered trademarks of  

Finishing Brands. ©2014 Finishing Brands. All rights reserved.

WARRANTY POLICY

DeVilbiss products are covered by Finishing Brands one year materials and workmanship limited warranty. 

 

The use of any parts or accessories, from a source other than Finishing Brands, will void all warranties. 

 

For specific warranty information please contact the closest Finishing Brands location listed below.

DeVilbiss is part of Finishing Brands, a global leader in innovative spray finishing 

technologies. For technical assistance or to locate an authorized distributor,  

contact one of our international sales and customer support locations below.

USA/Canada  

www.devilbiss.com 

 

info@finishingbrands.com 

 

Tel: 1-800-992-4657  

Fax: 1-888-246-5732

United Kingdom  

www.finishingbrands.eu 

 

info@finishingbrands.eu 

 

Tel: +44 (0)1202 571 111  

Fax: +44 (0)1202 573 488

China  

www.finishingbrands.com.cn 

 

mkt@finishingbrands.com.cn 

 

Tel: +8621-3373 0108  

Fax: +8621-3373 0308 

Mexico  

www.finishingbrands.com.mx 

 

sales@finishingbrands.com.mx 

 

Tel: 011 52 55 5321 2300  

Fax: 011 52 55 5310 4790

France  

www.finishingbrands.eu 

 

info@finishingbrands.eu 

 

Tel: +33(0)475 75 27 00  

Fax: +33(0)475 75 27 59

Japan  

www.ransburg.co.jp 

 

binks-devilbiss@ransburg.co.jp 

 

Tel: 081 45 785 6421  

Fax: 081 45 785 6517 

Brazil  

www.devilbiss.com.br 

 

sales@devilbiss.com.br  

Tel: +55 11 5641 2776  

Fax: 55 11 5641 1256

Germany  

www.finishingbrands.eu 

 

info@finishingbrands.eu 

 

Tel: +49 (0) 6074 403 1  

Fax: +49 (0) 6074 403 281

Australia  

www.finishingbrands.com.au 

 

sales@finishingbrands.com.au 

 

Tel: +61 (0) 2 8525 7555  

Fax: +61 (0) 2 8525 7500

Summary of Contents for MBC-510









Reviews: