Page 6 SB-2-243-F
TROUBLESHOOTING (cont'd)
CONDITION
CAUSE
CORRECTION
Thick, dimpled finish (orange
Gun too close to surface.
Check distance. Normally 6-8".
peel). Too much material
Air pressure too low.
Increase air pressure or reduce fluid pressure
coarsely atomized.
Improper thinner being used.
Follow paint manufacturer’s mixing instructions.
Material not properly mixed.
Follow paint manufacturer’s mixing instructions.
Surface rough, oily, dirty.
Properly clean and prepare.
Excessive fog
Too much, or too fast-trying thinner.
Remix properly.
Too much atomization air pressure.
Reduce pressure.
Unable to get round spray
Fan adjustment screw not seating
Clean or replace.
properly.
Air cap retaining ring loose.
Tighten.
* Most common problem.
KB-555 Alum.&
KB-545-SS S.S.
2 Qt Pressure Feed
Cups
Includes a 0-30 psi
gauge.
1 Qt. pressure feed
cups. 3/8" NPS (F), cam
lock lid. Requires KK-
4 9 8 0 .
JGA-4051, JGA-4056
(D, E, FF, FX) Premium
Fluid Tip/Needle Sets
Constructed of 300 S.S.
with U.H.M.W. polyeth-
ylene needle seat. Pro-
vides extended life and
better sealing character-
istics. See Chart 2.
2 Quart Hose Cleaner
used to clean the in-
side of hose and mate-
rial passages of gun.
Other sizes available.
Compatible with all paint
materials: contains no
silicone or petroleum
distillates to contami-
nate paint. MSDS avail-
able upon request.
Spray Gun Lube
SSL-10 (2 oz. bottle)
VS-531 Low
Pressure Fluid
Strainer
100 Mesh Screen
This strainer provides a
final filter for trapping
foreign particles in the
paint supply.
JGA-444
Fluid Tube
This tube combines
the fluid and air
hoses at gun handle
preventing dragging
hoses over work,
twisting lines and im-
proving overall gun
handling.
WR-103 Wrench
JGA-4005
Air Adjusting Valve
42882-214-K5 (3/8"),
42884-215-K10 (5/8")
Cleaning Brushes
These brushes are help-
ful in cleaning threads
and recesses of gun
body.
Allows air adjustment
at the gun. Replaces
JGA-132 plug.
Contains all necessary
tip, hose and nut sizes
used on or with gun.
KK-5033-28 for JGHV-101-28
KK-5033-33A for JGHV-101-33A
KK-5033-46MP for JGHV-101-46MP
KK-5033-83MP for JGHV-101-83MP
Air Cap Test Kit
UHMW
Polyethylene
Needle Seat
300 S.S.
ACCESSORIES
HD-503
SolventSaver®
TLC-576 Aluminum
Cup (Teflon Lined) &
TSC-591 Stainless Steel
Cup
Provides reduced
spring force (4 lbs.
verses 6 lbs.) for
easier trigger pull.
MSA-4-K10 Fluid
Needle Spring
(replaces MBD-19)
Quick Disconnect Approved for HVLP Guns (Air)
High Flow Type
HC-4419 1/4"
NPS(F)
HC-4699
1/4" NPT(M)
HC-1166
1/4" NPT(M)
HC-4700
1/4" NPT(F)
This 3 piece packing can
be used in place of Ref.
(22) JGV-463, 2 piece
packing.
JGA-4035-K5
Optional 3 Piece Packing
For use with 46MP air
cap. Eliminates need
of using SSG-8182-K5
O-Ring Ref. No. 5.
MSV-457-46 Optional Baffle
Scrubs
®
are a pre-moistened
hand cleaner towel for painters.
No water is needed.
29-3100 Scrubs
®
Hand Cleaner Towels
The purpose of this test kit
is to measure air cap atom-
izing air pressure at the
center air port of the air
cap. Used to confirm code
compliance and as a daily
quality control measure.
NIOSH-Certified, for
respiratory protection
in atmospheres not
immediately dangerous
to life.
Millennium 3000
Twin Cartridge
Paint Spray Respirator
9/04 ©2004
Inc. All rights reserved. Printed in U.S.A.
WARRANTY
This product is covered by DeVilbiss' 1 Year Limited Warranty.
DeVilbiss Worldwide Sales and Service Listing: www.devilbiss.com
Industrial Finishing
DeVilbiss has authorized distributors throughout the world. For
technical assistance or the distributor nearest you, see listing below.
U.S./Canada Technical Service Office:
195 Internationale Blvd., Glendale Heights, IL 60139
Toll-Free Telephone: 1-888-992-4657 (U.S.A. and Canada only)
Toll-Free Fax: 1-800-368-8401
