background image

Preparing the mixer

The Devine MX-4 and MX-6 mixers are developed for solo entertainers, broadcasting purposes and small 
recording environments. Thanks to the built-in USB MP3-player, it is possible to playback MP3-files. The 
compact construction of the MX-4 and MX-6 mixers makes it possible to place them on a desk or table 
during use. The rubber feet on the bottom of the mixer provide stability and sufficient grip. Therefore, the 
mixer will not move when operating the faders or encoders.

To get familiar with the several functions of the mixer, please examine the illustration below. Every function of
the mixer is provided with a number, which refers to the explanations on the next page. 

NOTE: 

The illustration shows the MX-4. The MX-6 is identical, but has two more mono channels.

Any information and illustrations shown in this user manual are subject to change without further notice.

User manual version: 1.0

Creation date + author initials: 27-08-2013 RV Revision date + author initials: 20-02-2014 RV

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

Summary of Contents for MX-4













Reviews: