3
MINIMUM GAUGE FOR CORD SETS
For Cable length (m):
7.5 15 25 30 45 60
Use Cable with minimum rating (Amperes)
Tool Amperes
0 - 3.4
7.5
7.5
7.5
7.5
7.5
7.5
3.5
-
5.0 7.5 7.5 7.5 7.5 10 15
5.1 - 7.0
10
10
10
10
15
15
7.1 - 12.0
15
15
15
15
20
20
12.1 - 20.0
20
20
20
20
25
–
Additional Safety Instructions for Drills
•
Hold power tools by insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring or its own cord.
Contact with a “live” wire will make exposed metal parts of the tool “live” and
shock the operator.
•
Keep handles dry, clean, free from oil and grease.
It is recommended to use
rubber gloves. This will enable better control.
•
Keep tool dry from sweat during use.
Reduce the risk of electric shock by
preventing perspiration or other liquids from entering the tool during use in hot/
humid conditions. Use wristbands, gloves, drying towels or cloths as necessary.
•
Use clamps or other practical way to secure and support the workpiece to a
stable platform.
Holding the work by hand or against your body is unstable and
may lead to loss of control.
WARNING: ALWAYS
use safety glasses. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
•
Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water.
Allowing dust to get into your mouth, eyes,
or lay on the skin may promote absorption of harmful chemicals.
WARNING:
Use of this tool can generate and/or disburse dust, which may cause
serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust exposure. Direct particles away from
face and body.
WARNING: ALWAYS wear proper personal hearing protection that conforms to
ANSI S12.6 (S3.19) during use.
Under some conditions and duration of use, noise
from this product may contribute to hearing loss.
WARNING:
We recommend the use of a residual current device with a residual
current rating of 30mA or less.
• The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
V .................... volts
A ...............amperes
Hz .................. hertz
W ..............watts
min ................ minutes
...........alternating current
........... direct current
...........alternating or direct current
................. Class I Construction
no ..............no load speed
......................
(grounded)
.............earthing terminal
................. Class II Construction
.............safety alert symbol
......................
(double insulated)
BPM ..........beats per minute
…/min ........... per minute
RPM ..........revolutions per minute
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Summary of Contents for D21002-XE
Page 1: ...D21002 XE D21008 XE DRILL INSTRUCTION MANUAL ...
Page 2: ......
Page 10: ...8 ...
Page 11: ...9 ...
