33
ENGLISH
3. Fit the depth adjustment rod (j) through the hole
in the depth stop clamp.
4. Adjust the drilling depth as shown.
5. Release the depth stop clamp.
Forward/reverse Slider (fig. 5)
1. Push the forward/reverse slider (c) to the
LH-side for forward (RH) rotation. See arrows
on tool.
2. Push the forward/reverse slider (c) to the
RH-side for reverse (LH) rotation.
WARNING:
Always wait until the motor
has come to a complete standstill
before changing the direction of rotation.
Fitting a Chuck Adapter and Chuck
(Sold Separately)
1. Screw a chuck onto the threaded end of the
chuck adapter.
2. Insert the connected chuck and adapter in the
tool as though it were a standard SDS Plus
®
bit.
3. To remove the chuck, proceed as for removing
a standard SDS Plus
®
bit.
WARNING:
Never use standard chucks
in the hammerdrilling mode.
Consult your dealer for further information on the
appropriate accessories.
Replacing the Tool Holder with the
Chuck (fig. 6)
D25414 AND D25415 ONLY
1. Turn the locking collar (l) into the unlocking
position and pull the tool holder/locking
sleeve (g) off.
2. Push the chuck (m) onto the spindle and turn
the locking collar into the locking position.
3. To replace the chuck with the tool holder, first
remove the chuck the same way as the tool
holder was removed. Then place the tool holder
the same way as the chuck was placed.
WARNING:
Never use standard chucks
in the hammerdrilling mode.
Replacing the Dust Cover (fig. 1, 4)
The dust cover (n) prevents dust ingress into the
mechanism. Replace a worn dust cover immediately.
1. Pull back the tool holder locking sleeve (g) and
pull the dust cover (n) off.
2. Fit the new dust cover.
2. Rotate the chisel in the desired position.
3. Set the mode selector switch (d) to the
hammering only position.
4. Twist the chisel until it locks in position.
Inserting and Removing SDS Plus
®
Accessories (fig. 4)
This tool uses SDS Plus
®
accessories (refer to
the inset in figure 4 for a cross-section of an SDS
Plus
®
bit shank). We recommend using professional
accessories only.
1. Clean and grease the bit shank.
2. Insert the bit shank into the tool holder/locking
sleeve (g).
3. Push the bit down and turn it slightly until it fits
into the slots.
4. Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
5. To remove a bit, pull back the tool holder/
locking sleeve (g) and pull out the bit.
WARNING:
Always wear gloves when
you change accessories. The exposed
metal parts on the tool and accessory
may become extremly hot during
operation.
Fitting the Side Handle (fig. 1)
The side handle (f) can be fitted to suit both RH- and
LH-users.
WARNING:
Do not use the tool without
the side handle properly assembled.
1. Loosen the side handle.
2.
For RH-users:
slide the side handle clamp
over the collar behind the tool holder, handle at
the left.
For LH-users:
slide the side handle clamp over
the collar behind the tool holder, handle at the
right.
3. Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth (fig. 4)
D25413, D25414, D25415 ONLY
1. Insert the required drill bit as described above.
2. Press the depth stop clamp (k) and keep it
depressed.
Summary of Contents for D25413
Page 1: ...D25413 D25414 D25415 D25430 ...
Page 4: ...2 Figure 5 Figure 6 Figure 7 c b f l m g ...
Page 158: ...156 ...
Page 159: ...157 ...
