ENGLISH
41
DO NOT
let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your D
E
WALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
WARNING:
115 V units have to
be operated via a fail-safe isolating
transformer with an earth screen
between the primary and secondary
winding.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D
E
WALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING:
No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–
core extension cable suitable for the power input of
this tool (see technical data).The minimum conductor
size is 1.5 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs.
Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Cutters
The tooling can be used with the complete range
of commercial cutters (e.g: straight, rebate, profile
cutter, slotter cutter or grooved knife) with the
following technical data:
1. Shank diameter 6–8 mm
2. Cutter speed of min. 30000/min
WARNING:
Max diameter to use:
•
For straight-cutters, rabbet-cutters,
profile cutters, the maximum shank
diameter
MUST
be 8 mm, the
maximum diameter
MUST
be
36 mm, the maximum cutting
depth
MUST
be 10 mm.
•
For slotter cutters, the maximum
shank diameter
MUST
be 8 mm and
the maximum diameter
MUST
be 25 mm.
•
For grooved knives, the maximum
shank diameter
MUST
be 8 mm, the
maximum diameter
MUST
be
40 mm and the maximum cutting
width
MUST
be 4 mm.
Motor Quick Release (fi g. 2)
WARNING: To reduce the risk of
injury, turn unit off and disconnect it
from power source before installing
and removing accessories, before
adjusting or when making repairs.
An accidental start-up can cause injury.
1. Open the locking lever (i) on the base.
2. Grasp the motor unit with one hand, depressing
both quick release tabs (a).
3. With the other hand, grasp the base and pull
motor from the base.
Cutter Installation and Removal
(fi g. 3)
WARNING: To reduce the risk of
injury, turn unit off and disconnect it
from power source before installing
and removing accessories, before
adjusting or when making repairs.
An accidental start-up can cause injury.
TO INSTALL THE CUTTER
1. Remove the motor unit from the base unit, refer
Motor Quick Release,
if needed.
2. Clean and insert the round shank of the desired
router cutter into the loosened collet as far as it
will go and then pull it out about 1.6 mm.
Summary of Contents for D26200
