19
EngLIsh
Description (Fig. A)
WARNING:
Never modify the power tool or any part of it.
Damage or personal injury could result.
1
On/off switch
2
Speed control dial
3
Sanding pad
4
Dust filter cassette
Intended Use
Your detail sander D26430 has been designed for quick sanding
of wood, metal and plastics in a professional environment.
DO nOt
use under wet conditions or in the presence of
flammable liquids or gases.
These sanders are professional power tools.
DO nOt
let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm.
This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Fitting Sanding Sheets (Fig. B)
The tool uses hook and loop sanding sheets.
1. Place the tool on a table, sanding pad
3
up.
2. Place the sanding sheet
5
directly on top of the
sanding pad.
3. Hold the sanding pad with one hand and align the dust
extraction holes.
4. Press the sheet firmly onto the sanding pad.
Rotating the Sanding Pad (Fig. A)
The sanding pad is adjustable in 60° increments.
1. Hold the tool upside down.
2. Lift the sanding pad
3
up from the tool.
3. At the same time, rotate the sanding pad in the
desired direction.
4. Release the sanding pad.
5. Move the sanding pad back and forth slightly untile it
engages in position.
Mounting the Louvre Attachment (Fig. C)
Fitted with sanding sheets on both sides, the louvre attachment
is used to sand crevices. The louvre attachment is available as
an option.
1. Place the tool on a table, sanding pad
3
up.
2. Loosen the screw
7
and remove it using the hex
key provided.
3. Remove the spring
8
from the recess in the sanding pad.
4. Remove the sanding pad.
5. Locate the louvre attachment
9
so that it engages in
position and cannot be turned.
6. Place the spring
8
in the recess.
7. Fit the screw
7
and tighten it.
Setting the Electronic Speed Control Dial
(Fig. D)
The speed is infinitely variable from 14000–22000 min
-1
using
the electronic speed control dial
2
.
1. Turn the electronic speed control dial to the required level.
The correct setting, however, is a matter of experience.
2. Generally, harder materials require a higher setting.
Dust Extraction (Fig. E–G)
WARNING:
Since woodworking with a sander produces
dust, always install a dustbag designed in compliance
with the applicable directives regarding dust emission.
WARNING:
Do not use a dustbag or vacuum extractor
without proper spark protection when sanding metal.
1. Slide a dust filter
10
into the cassette
4
as shown.
2. Fit the cover
11
onto the cassette.
3. Attach the cassette
4
to the dust extraction outlet
12
.
4. Push the cassette firmly until it locks in position.
Fitting the Dust Extraction Adaptor (Fig. G)
The dust extraction adaptor
13
is available as an option.
1. Remove the dust filter cassette, if fitted.
2. Attach the adaptor
13
to the dust extraction outlet
12
.
3. Pass the screw
14
through the adaptor outlet
15
into the
mounting hole
16
. Tighten the screw.
4. Connect the hose of a suitable dust extraction system to
the adaptor.
5. Alternatively, when no dust extration is required, place the
end cap
17
on the adaptor outlet
15
.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
Be sure the
