EnGLIsH
4
5
2.
Slide it into the handle until the battery pack is firmly
seated in the tool and ensure that you hear the lock
snap into place.
To Remove the Battery Pack from the Tool
1.
Press the release button
2
and firmly pull the battery
pack out of the tool handle.
2.
Insert battery pack into the charger as described in
the charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D
e
WALT battery packs include a fuel gauge which
consists of three green LED lights that indicate the level
of charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button. A combination of the three green LED lights will
illuminate designating the level of charge left. When the
level of charge in the battery is below the usable limit,
the fuel gauge will not illuminate and the battery will
need to be recharged.
nOTE: The fuel gauge is only an indication of the charge
left on the battery pack. It does not indicate tool
functionality and is subject to variation based on
product components, temperature and end-user
application.
Belt Hook and Magnetic Bit Holder
(Fig. A)
(Optional
Accessories)
WARNING: To reduce the risk of serious
personal injury, DO NOT suspend tool
overhead or suspend objects from the belt
hook. ONLY hang tool’s belt hook
from a
work belt.
WARNING: To reduce the risk of serious
personal injury, ensure the screw holding the
belt hook is secure. IMPORTanT: When attaching or
replacing a belt hook or magnetic bit holder, use only
the screw that is provided. Be sure to securely tighten
the screw.
A belt hook
11
and magnetic bit holder
13
can be be
attached to either side of the tool using only the screw
12
provided, to accommodate left- or right-handed
users. If the hook or magnetic bit holder is not desired at
all, it can be removed from the tool.
To move belt hook or magnetic bit holder, remove the
screw
12
that holds it in place then reassemble on the
opposite side. Be sure to securely tighten the screw.
Installing a Bit or Accessory into a
Keyless Chuck (Fig. D)
WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of
the chuck and turning the tool on. Damage to the
chuck and personal injury may result. Always lock off
trigger switch and disconnect tool from power source
when
changing acces sories.
WARNING: Always ensure the bit is secure before
starting the tool. A loose bit may eject from tool
causing possible personal injury.
Your tool features a keyless chuck
10
with one rotating
sleeve
9
for one-handed operation of the chuck. To
insert a drill bit or other accessory, follow these steps.
1.
Turn tool off and remove battery pack.
2.
Grasp the black sleeve of the chuck with one hand and
use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3.
Insert the accessory about 19 mm into the chuck and
tighten securely by rotating the chuck sleeve
clockwise with one hand while holding the tool with
the other. Your tool is equipped with an automatic
spindle lock mechanism. This allows you to open and
close the chuck with one hand.
Be sure to tighten chuck with one hand on the chuck
sleeve and one hand holding the tool for maximum
tightness. To release the accessory, repeat steps 1 and 2
above.
Speed Selection (Fig. A)
The tool features two speed settings for greater
versatility. nOTE: Do not change speeds when the tool
is running. Always allow the tool to come to a
complete stop before changing speed.
1.
To select speed 1 (high torque setting), turn the tool
off and permit it to stop. Slide the speed selector
7
back (away from the chuck).
2.
To select speed 2 (high speed setting), turn the tool
off and permit it to stop. Slide the speed selector
7
forward (toward the chuck).
Summary of Contents for DCD708
