18
GB
Troubleshooting
The Laser Does Not Turn On
• Fully-charge the battery pack and then reinstall it in
the laser unit.
•
If the laser unit is heated above 120˚F (50˚C), the
unit will not turn on. If the laser has been stored in
extremely hot temperatures, allow it to cool. The
laser level will not be damaged by pressing the on/
off button before cooling to its proper operating
temperature.
The Laser Beams Flash
The lasers are designed to self-level up to an average
of 4° in all directions If the laser is tilted so much that
the internal mechanism cannot level itself, the laser
beams will flash indicating that the tilt range has been
exceeded. THE FLASHING BEAMS CREATED BY
THE LASER ARE NOT LEVEL OR PLUMB AND
SHOULD NOT BE USED FOR DETERMINING OR
MARKING LEVEL OR PLUMB. Try repositioning the
laser on a more level surface.
The Laser Beams Will Not Stop Moving
The laser is a precision instrument. Therefore, if it is
not positioned on a stable (and motionless) surface,
the laser will continue to try to find level. If the beam
will not stop moving, try placing the laser on a more
stable surface. Also, try to make sure that the surface
is relatively flat, so that the laser is stable.
The Battery Meter LEDs Flash
When all 4 LEDs continuously flash on the Battery
Meter this indicates that the unit has not been fully
powered off using the Power/Transport Lock switch
(Figure
C
2
). The Power/Transport Lock switch
should always be placed in the LOCKED/OFF position
when the laser is not in use.
Accessories
The laser is equipped with both 1/4 - 20 and 5/8 - 11
female threads on the bottom of the unit (Figure
K
).
This thread is to accommodate current or future
D
E
Walt accessories. Only use D
E
Walt accessories
specified for use with this product. Follow the
directions included with the accessory.
WARNING:
Since accessories, other than those
offered by D
E
Walt, have not been tested with
this product, use of such accessories with this
tool could be hazardous. To reduce the risk of
injury, only D
E
Walt recommended accessories
should be used with this product.
If you need any assistance in locating any accessory,
please contact your nearest D
E
WALT service center or
go to www.2helpU.com.
Target Card
Some laser kits include a Laser Target Card (Figure
M
) to aid in locating and marking the laser beam.
The target card enhances the visibility of the laser
beam as the beam crosses over the card. The card
is marked with standard and metric scales. The laser
beam passes through the red plastic and reflects off of
the reflective tape on the reverse side. The magnet at
the top of the card is designed to hold the target card
to ceiling track or steel studs to determine plumb and
level positions. For best performance when using the
Target Card, the
D
e
WALT
logo should be facing you.
Laser Enhancement Glasses
Some laser kits include Laser En hancement Glasses
(Figure
N
). These glasses improve the visibility of
the laser beam under bright light conditions or over
long distances when the laser is used for interior
applications. These glasses are not required to operate
the laser.
Summary of Contents for DCE089G18
