background image

English

1

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk 
of personal injury or property damage.

 

DANGER:

 Indicates an imminently hazardous situation which, if not avoided, 

will 

result in 

death or serious injury

.

 

WARNING:

 Indicates a potentially hazardous situation which, if not avoided, 

could

 result in 

death or serious injury

.

 

CAUTION:

 Indicates a potentially hazardous situation which, if not avoided, 

may

 result in 

minor or moderate injury

.

 

(Used without word) Indicates a safety related message.

NOTICE:

 Indicates a practice 

not related to personal injury

 which, if not avoided, 

may

 result in 

property damage

.

 

WARNING! Read all safety warnings, 
instructions, illustrations and specifications 
provided with this power tool.  

Failure to follow all 

instructions listed below may result in electric shock, 
fire and/or serious injury.

WARNING:

 To reduce the risk of injury, read the 

instruction manual.

if you have any questions or comments about this or 
any 

D

e

WALT

 tool, call us toll free at:  

1-800-4-

D

e

WALT

 (1-800-433-9258).

Expander head

Expander cone

Handle

Trigger switch

Trigger lock

LED

Hang hook

Belt hook attachment 
location

Battery

10 

Battery release

Fig. A

4

5

9

1

2

7

8

3

6

10

Summary of Contents for DCE400B













Reviews: