28
ENGLISH
TO PROGRAMME THE CLOCK
1. Turn power on (see
Power/Volume
Adjustment
).
2. Push and hold clock button (e) until the LCD
display (h) begins flashing.
3. Press the left arrow button repeatedly to
increment the hour of the displayed time
or press and hold the button to increment
continuously. Use the right arrow button to
adjust the minute in the same manner.
NOTE:
If you do not press a button within
5 seconds, the clock programming feature will
automatically return to the previous setting.
4. Once the time is set, push and hold the clock
button until the time on the LCD display stops
flashing.
PLAYING AUDIO THROUGH AN EXTERNAL DEVICE
To play your device through the radio's speakers,
connect it to the auxiliary port (l) using a 3.5 mm
auxiliary audio cable and set the mode to AUX. Refer
to
Mode Function
.
Important Radio Notes
1. The radio will run up to 8 hours on a fully
charged 4.0 amp hour battery. Using batteries
of lower voltage or capacity will produce less
run time.
2. Reception will vary depending on location and
strength of radio signal.
3. Certain generators may cause background
noise.
4. AM reception will most likely be clearer when
powered by a battery pack.
5. To use the auxiliary port (l), plug the output jack
from a CD or iPod
®
*/MP3 player into the port
(fig. 3). The sound from the external source
plays through the speakers of the DCR019.
* iPod is a registered trademark of Apple Inc.
MAINTENANCE
Your D
E
WALT radio has been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper care.
Service Notes
This product is not user serviceable. There are no
user serviceable parts inside the radio. Servicing
at an authorised service centre is required to avoid
damage to static sensitive internal components.
Operating the Radio (fi g. 1, 3)
POWER/VOLUME ADJUSTMENT
1. To turn the radio on, press the power button (a).
2. Turn the dial (b) clockwise to increase the
volume. To decrease the volume, turn
anticlockwise.
MODE FUNCTION
To choose one of the mode functions (FM, AM, or
AUX), push the mode button (d) until the desired
function is found. For example, if the radio is on FM,
seen in upper left portion of LCD display (h), push
the mode button twice to change to AM.
TUNE OR SEEK FUNCTION
There are two methods for finding the desired
frequency.
To Tune:
Push the right arrow to move the tuner up
the frequency band. Push the left arrow to move the
tuner down the frequency band.
To Seek:
Press the right arrow button (c) once and
release. The tuner frequency will increase to seek the
first radio station with acceptable clarity and stop at
that station. The right arrow button may be pressed
again to continue seeking a radio station at higher
frequencies. The left arrow button may be pressed
to seek radio stations at lower frequencies. The seek
function is available in AM and FM modes.
TO PROGRAMME THE PRESETS
Ten FM and five AM radio stations may be
independently programmed into the radio's memory.
Once programmed, the memory button can be used
to quickly change to the desired preset station.
1. Turn on radio by pressing the ON/OFF
button (a).
2. Set the radio to desired station Refer to
Tune
or Seek Function
.
3. Press and hold the preset button (g) until the
memory number begins to flash in the LCD
display (h).
4. With the memory number flashing, use the
arrow buttons to select the desired memory
number.
5. Once the desired memory number is displayed,
press and hold the preset button until the
flashing stops. The preset is now saved.
6. Repeat steps 2 through 5 to preset additional
stations to memory.
Summary of Contents for DCR019
Page 1: ...DCR019 ...
Page 3: ...1 Figure 1 Figure 2 Figure 3 o m l n h f c b a d e g ...
Page 4: ...2 Figure 4 j i k ...
Page 131: ...129 ...
