ENGLISH
34
Inserting and Removing the
Battery Pack from the Tool (fi g. 3)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
NOTE:
Make sure your battery pack (c) is fully
charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack with the rails inside the
handle.
2. Slide it firmly into place until you hear the lock
snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release button (b) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
Belt Hook
(Optional Accessory, fi g. 1A)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
WARNING: To reduce the risk of
serious personal injury, DO NOT
suspend tool overhead or suspend
objects from the belt hook. ONLY
hang tool’s belt hook from a work
belt.
WARNING: To reduce the risk of
serious personal injury, ensure
the screw holding the belt hook is
secure.
IMPORTANT:
When attaching or replacing the belt
hook, use only the screw (p) that is provided. Be
sure to securely tighten screw.
The belt hook (o) can be be attached to either side
of the tool using only the screw (p) provided, to
accommodate left- or right- handed users. If the
hook is not desired at all, it can be removed from
the tool.
To move belt hook, remove the screw (p) that holds
the belt hook in place then reassemble on the
opposite side. Be sure to securely tighten screw.
OPERATION
Instructions for Use
WARNING:
Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
Proper Hand Position (fi g. 4)
WARNING:
To reduce the risk of
serious personal injury,
ALWAYS
use
proper hand position as shown.
WARNING:
To reduce the risk of
serious personal injury,
ALWAYS
hold
securely.
Proper hand position requires one hand on the main
handle as shown in figure 4.
Select Operating Mode (fi g. 1B)
Read the following steps before operating the IR
thermometer.
CHOOSE UNITS OF MEASUREMENT
Turn the unit on by engaging the trigger. Once the
screen comes on, push the C/F button until the unit
of measurement is on the correct setting for the
application.
CHOOSE EMISSIVITY
Turn the unit on by engaging the trigger; once
the screen comes on push the EMS button for
emissivity adjustment. When then EMS is flashing
on the screen, use the up or down arrow buttons
to choose the emissivity. Please refer to the chart in
order to choose the correct emissivity. Remember,
emissivity is adjustable by 0.01.
NOMINAL EMISSIVITY TABLE
MATERIAL
VALUE
MATERIAL
VALUE
Default****
0.95
Lead*
0.50
Aluminum*
0.30
Oil 0.94
Asbestos
0.95
Paint
0.93
Asphalt
0.95
Plastic**
0.95
Brass*
0.50
Rubber
0.95
Ceramic
0.95
Sand 0.90
Concrete
0.95
Steel*
0.80
Copper*
0.60
Water 0.93
Glass (plate)
0.85
Wood***
0.94
Iron*
0.70
Summary of Contents for DCT414
