DeWalt DCV501, Instruction Manual

9

English

Cleaning/Emptying the Dust Bowl and 

Filter (Fig. D, E, J, K)

WARNING:

 Projectile/Respiratory Hazard: Never use 

the vac without its filter.

nOTE: 

The filter is reusable, do not confuse it with a 

disposable dust bag, and do not throw it away when the 
product is emptied. We recommend that you replace the 
filter every 6–9 months depending on frequency of use.

Removing Filter

1.  Place the vacuum over a trash bin and remove the 

dust bowl 

 2 

 from the main housing by pressing the 

dust bowl release button 

 3 

 on the handle and remove 

the dust bowl by pulling the dust bowl away from the 
main housing.

2.  Remove the filter assembly 

 4 

 by pulling it out of the 

dust bowl.

3.  Twist counterclockwise and pull the filter cap 

 21 

 to 

seperate it from the filter 

 20 

.

install Filter

1.  Attach the filter cap onto the filter and rotate it clockwise 

to lock it firmly into position.

2.  Push the filter assembly into the dust bowl.
3.  Install the dust bowl onto the main housing and lock it 

firmly into position.

Cleaning
iMPORTAnT: 

Maximum dust collection will only be 

obtained with a clean filter and an empty dust bowl. If dust 
begins to fall back out of the product after it is switched off, 
this indicates that the bowl is full and requires emptying.

1.  Once the filter is removed from the dust bowl, shake off 

or lightly brush any dust from the filter. 

2.  Empty any dust from the dust bowl 

 2 

 into a trash bin 

and wash if necessary. 

3.  Rinse out the dust bowl with warm soapy water. Ensure 

that the dust bowl is completely dry before using.

4.  Wash the filters regularly using warm, soapy water and 

ensure that it is completely dry before using again. The 
cleaner the filter is, the better the product will perform. 

5.  It is very important that the filters are completely dry and 

correctly in position before use.

6.  Ensure the filters are completely dry for 12 hours 

before refitting.

Replacement HEPA filter: DCV5011H

Cleaning

WARNING:

 Blow dirt and dust out of all air vents with 

clean, dry air at least once a week. To minimize the risk 
of eye injury, always wear ANSI Z87.1 approved eye 
protection when performing this procedure.

WARNING:

 Never use solvents or other harsh 

chemicals for cleaning the non‑metallic parts of the 
tool. These chemicals may weaken the plastic materials 
used in these parts. Use a cloth dampened only with 
water and mild soap. Never let any liquid get inside the 
tool; never immerse any part of the tool into a liquid.

Storing the Dust Extractor

WARNING:

a )  Empty the dust collection box before storing the dust 

extractor.

b )  Always store your dust extractor with the batteries 

removed.

c )  Store the tool and batteries in a place that is as cool 

and dry as possible.

d )  Store the tool and batteries in a place that cannot be 

accessed by children or unauthorised persons.

e )  Check the tool and batteries for damage after long 

periods of storage.

f )  Refer to the

 Battery Packs, Transportation 

section of 

this manual for further information.

MAINTENANCE

WARNING: To reduce the risk of serious personal 
injury, turn unit off and remove the battery pack 
before making any adjustments or removing/
installing attachments or accessories.

 An 

accidental start‑up can cause injury.

Your 

D

e

WALT

 power tool has been designed to operate 

over a long period of time with a minimum of maintenance. 
Continuous satisfactory operation depends upon proper tool 
care and regular cleaning.

On/Off Switch (Fig. I)

nOTE: 

This product is for dry pick‑up only. 

•  To switch the vac on, slide the On/Off switch 

 1 

 forward.

•  To switch the vac off, slide the On/Off switch back.

Installing and Removing the Battery Pack 

(Fig. H)

nOTE:

 For best results, make sure your battery pack is 

fully charged.
To install the battery pack 

 5 

 into the tool handle, align the 

battery pack with the rails inside the tool’s handle and slide it 
into the handle until the battery pack is firmly seated in the 
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release 
button 

 6 

 and firmly pull the battery pack out of the tool 

handle. Insert it into the charger as described in the charger 
section of this manual.

OPERATION (FIG. A)

WARNING:

To Reduce The Risk Of Electric Shock – 

Use indoors only.

WARNING:

To reduce the risk of serious personal 

injury, turn unit OFF before making any 
adjustments or removing/installing attachments 
or accessories.

 An accidental start‑up can 

cause injury.

WARNING:

 Projectile/Respiratory Hazard: Never use 

the vac without its filter.