ENGLISH
32
SPEED/ROTATION BUTTON
The speed/rotation button (h) is used to adjust the
rotation speed of the laser beam through its 3 preset
speeds.
The head speed will cycle through 3 speeds, then
repeat the sequence as the speed/rotation button is
pressed.
REMEMBER:
Slow Speed = Bright Beam
Fast Speed = Solid Beam
NOTE:
The speed/rotation button performs the
same function as the speed/rotation button on the
remote control.
SCAN MODE BUTTON
The scan mode button (i) is used to make the laser
head sweep back and forth, creating a short, bright
laser line. This short line is much brighter and more
visible than when the unit is in full rotation mode.
Using Scan Mode:
To enter scan mode, push and release the
scan mode button. To exit scan mode, push
and release the button again.
The size and direction of the scan zone can
be controlled with the arrow buttons on the
laser unit control panel or the remote control.
For a more detailed explanation, refer to
Using the Wireless Remote Control
.
The size and direction of the scan zone can
also be controlled manually with the User
Defined Scan Mode:
1. Set the laser unit at 0 rpm (pointer mode).
2.
Manually rotate the laser head to position
the laser beam at one edge of the desired
scan zone.
3.
Press and hold the scan button on the
laser unit control panel. While holding
down the scan button, manually rotate
the laser head to the opposite edge of
the desired scan zone.
4. Release the scan button.
5.
The laser will scan between the two
selected points.
IMPORTANT:
The remote control cannot be
used for User Defined Scan Mode.
LOW BATTERY INDICATION
When the batteries approach end of life (g), the
power LED (f) will begin to flash. When this signal is
observed, only a short period of runtime is left before
the unit will completely shut down. The batteries
should be replaced with new batteries as soon as
possible.
Using the Wireless Remote Control
(fi g. 1)
The remote control allows one person to operate
and setup the laser from a distance. The remote
control features four arrows (m, n), speed/rotation
button (o), scan mode button (p) and a manual
mode button (l).
REMOTE CONTROL: ARROW BUTTONS
The arrow buttons (m, n) are used for different
functions depending on the operating mode of the
laser unit.
In Self-Leveling Horizontal Mode:
The up and down arrows (m) adjust the
length of the laser line in Scan Mode.
The left and right arrows (n) adjust the
direction of the laser beam in Scan Mode or
Pointing Mode (0 rpm).
In Self-Leveling Vertical Mode:
The up and down arrows (m) adjust the
position of the laser line in Scan Mode.
The left and right arrows (n) move the laser
beam left and right.
REMOTE CONTROL: SPEED/ROTATION BUTTON
The speed/rotation button (o) is used to adjust
the speed of the laser beam through its 3 preset
speeds.
NOTE:
The speed/rotation button performs the
same function as the speed/rotation button on the
control panel of the laser unit.
REMOTE CONTROL: SCAN MODE BUTTON
The scan mode button (p) is used to make the laser
head sweep back and forth, creating a short, bright
laser line. This short line is much brighter and more
visible than when the unit is in full rotation mode.
Using Scan Mode:
To enter scan mode, push and release the
scan mode button. To exit scan mode, push
and release the button again.
The size and direction of the scan zone can
be controlled with the arrow buttons on the
laser unit control panel or the remote control.
For a more detailed explanation, refer to
Arrow Buttons
under
Laser Control Panel
Buttons
.
IMPORTANT:
The remote control cannot be
used for User Defined Scan Mode.
Summary of Contents for DW075
