ENGLISH
52
2. Position the rotary laser securely on the floor
approximately 1 m (3') from the wall.
3. Turn the laser on, and point the dot at the
mark on the bottom of the wall. Then, using the
up/down arrows on the remote control, rotate
the dot upwards. If the centre of the dot scans
over the mark on the top of the wall, the laser is
properly calibrated.
NOTE:
This check should be done with a wall no
shorter than the tallest wall for which this laser will
be used.
Cleaning
WARNING:
•
Unplug the charger before cleaning.
Dirt and grease may be removed
from the exterior of the charger using
a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
•
Remove the battery pack before
cleaning your laser unit.
•
Never use solvents or other harsh
chemicals for cleaning the non-
metallic parts of the laser. Use a cloth
dampened only with water and mild
soap.
•
Never let any liquid get inside the
unit; never immerse any part of the
unit into a liquid.
•
Never use compressed air to clean
the laser.
•
Keep the ventilation slots clear and
regularly clean the housing with a
soft cloth.
•
The flexible rubber shield can be
cleaned with a wet lint-free cloth
such as a cotton cloth. USE WATER
ONLY — DO NOT use cleansers
or solvents. Allow the unit to air dry
before storing.
•
Under some conditions, the glass
lens inside the rotary head may
collect some dirt or debris. This will
affect beam quality and operating
range. The lens should be cleaned
with a cotton swab moistened with
water.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your D
E
WALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
D
E
WALT provides a facility for the collection and
recycling of D
E
WALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
D
E
WALT office at the address indicated in this
manual. Alternatively, a list of authorised D
E
WALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Run the battery pack down completely, then
remove it from the tool.
• Li-Ion, NiCd and NiMH cells are recyclable. Take
them to your dealer or a local recycling station.
The collected battery packs will be recycled or
disposed of properly.
Summary of Contents for DW079
