18
E N G L I S H
en - 5
• Fit the depth adjustment rod (6) through the hole
in the side handle clamp.
• Adjust the drilling depth as shown.
• Tighten the side handle.
Forward/Reverse-lever (fig. F)
• Push the forward/reverse-lever (3) to the LH-side
for forward (RH) rotation. See arrows on tool.
• Push the forward/reverse-lever (3) to the RH-side
for reverse (LH) rotation.
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Replacing the dust cover (fig. C)
The dust cover (7) prevents dust ingress into the
mechanism. Replace a worn dust cover immediately.
• Pull back the tool holder locking sleeve (9) and
pull the dust cover (7) off.
• Fit the new dust cover.
• Release the tool holder locking sleeve.
Instructions for use
• Always observe the safety instructions
and applicable regulations.
• Be aware of the location of pipework and
wiring.
• Apply only a gentle pressure to the tool
(approx. 2-3 kg). Excessive force does
not speed up drilling but decreases tool
performance and may shorten tool life.
• Do not drill or drive too deep to prevent
damage to the dust cover.
Switching ON and OFF (fig. A)
• To run the tool, press the variable speed switch (1).
The pressure exerted on the variable speed
switch determines the tool speed.
• If necessary, press the lock-on button (2) for
continuous operation and release the variable
speed switch. The lock-on button works only in
full speed, forward rotation.
• To stop the tool, release the variable speed switch.
• To stop the tool in continuous operation, press
the variable speed switch briefly and release it.
Always switch OFF the tool when work is finished
and before unplugging.
Hammer drilling (fig. A)
• Select the hammer drilling mode (4).
• Insert the appropriate SDS-plus
®
bit. For best
results use high quality carbide-tipped bits.
• Mark the spot where the hole is to be drilled.
• Press the tool against the workpiece.
• Switch the tool ON by pressing the variable speed
switch (1). The hammer mechanism should run
smoothly and the tool should not bounce. If
necessary, increase the pressure on the switch.
Rotary drilling (fig. A)
• Select the rotary drilling mode (4).
• Proceed as described for hammer drilling.
Special SDS-plus
®
adaptors with threaded
sections are available for use with standard 10 or
13 mm chucks to enable straight shank bits to
be used.
Never use standard chucks in the
hammer drilling mode.
Screwdriving (fig. A)
• Select the rotary drilling mode (4).
• Select the direction of rotation (3).
• Insert the special SDS-plus
®
screwdriving
adaptor for use with hexagonal screwdriver bits.
• Insert the appropriate screwdriver bit into the
adaptor. When driving slotted head screws
always use bits with a finder sleeve.
• Gently press the variable speed switch (1) to
prevent damage to the screw head. In reverse
(LH) rotation the tool speed is automatically
reduced for easy screw removal.
Chipping and chiselling
• To switch from hammer drilling to chiselling, first
insert the SDS-plus
®
chisel and check if it is
properly locked.
• When switching from hammer drilling mode to
chiselling mode, turn the chisel to the desired
position. If you find resistance during mode change,
turn the chisel slightly to engage the spindle lock.
• The hammer is only for light chiselling
applications.
• The forward/reverse switch must be in the
forward position when chiselling (in reverse
the unit does not reach full power).
Summary of Contents for DW567K
