DeWalt DWE46172, Original Instructions Manual

16

EngLIsh

Dust Extraction (Fig. F–H)

WARNING: 

Use only power tools recommended by 

D

e

WALT

 with this attachment. For technical specifications 

refer to 

technical Data.

For more information about 

D

e

WALT

 power tools compatible 

with this attachment, please contact one of the authorised 
services centres listed on the back cover or refer to the full 
details of our after-sales service available on the Internet at: 

www.2helpU.com

.

WARNING:

 This attachment must be used with a dust 

extractor system class M suitable for mineral dust. 
ALWAYS wear certified safety face or dust mask.

nOtE: 

Ensure hose connection is secure.

nOtE: 

The amount of dust retained by the dust extractor 

vacuum is dependent on its filter system. Refer to the dust 
extractor vacuum instruction manual for more information.
All 

D

e

WALT

 dust collection shrouds are designed to connect 

and secure easily with the 

D

e

WALT

 universal DWV9000 

connector. The DWV9000 connector comes pre-installed on 
some 

D

e

WALT

 dust extractors. Consult your local dealer for 

compatible extractors.

Connecting the DWV9000 onto the Shroud 
(Fig. F)

nOtE:

If the DWV9000 is not installed on your dust 

extractor hose, refer to

Installing the DWV9000 on a Dust 

Extraction hose.

1.  With the DWV9000 connector 

 9 

 unlocked, slide it onto the 

shroud's dust port 

 4 

.

2.  Lock the DWV9000 connector 

 9 

 to secure.

Installing the DWV9000 on a Dust Extraction 
Hose (Fig. G–H)

The DWV9000 can be attached to a 32 mm dust 
extraction hose.

For 32 mm hoses:

1.   Remove the existing hose connector 

 10 

 by twisting 

clockwise, or if connector is permanently attached, remove 
by cutting.

2.   Install the universal DWV9000 connector 

 9 

 onto the hose 

by turning anticlockwise.

OPERATION

WARNING: To reduce the risk of injury, ALWAYS turn 
off tool and disconnect the tool from the power 
source before making any adjustments or removing 
or installing attachments or accessories. This applies 
to both the grinder and the dust extractor. 

Such 

preventative safety measures reduce the risk of starting the 
tool accidentally.

WARNING: 

For your own safety, read the instruction 

manual for both the grinding tool and the dust extractor 
before using any accessory. Failure to heed these warnings 
may result in personal injury and serious damage to the 
tool and the accessory. When servicing this tool, use only 
identical replacement parts.

nOtE: 

The amount of dust retained by the dust extractor 

vacuum is dependent on its filter system. Refer to the dust 
extractor instruction manual for more information.

1.  Ensure all assembly instructions have been completed.
2.  Turn the dust extractor vacuum on as instructed in the dust 

extractor vacuum instruction manual.

3.  Turn the tool on as instructed in the tool instruction manual 

and allow it to reach full speed before making contact with 
work surface.

4.  Place the surface grinding shroud to flat work surface such 

as a floor or wall and begin grinding.

5.  When surface grinding is complete, turn the tool off and 

disconnect from the power source. Allow the tool to stop 
rotating before laying it down.

nOtE: 

The surface grinding shroud and dust extractor vacuum 

will only be effective when used with a diamond surface cup 
wheel on a flat surface.

MAINTENANCE

Your 

D

e

WALT

 power tool has been designed to operate 

over a long period of time with a minimum of maintenance. 
Continuous satisfactory operation depends upon proper tool 
care and regular cleaning.

WARNING: To reduce the risk of injury, ALWAYS turn 
off tool and disconnect the tool from the power 
source before making any adjustments or removing 
or installing attachments or accessories. This applies 
to both the grinder and the dust extractor vacuum. 

Such preventative safety measures reduce the risk of 
starting the tool accidentally.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING:

 Blow dirt and dust out of the main housing 

with dry air as often as dirt is seen collecting in and around 
the air vents. Wear approved eye protection and approved 
dust mask when performing this procedure.

WARNING: 

Never use solvents or other harsh chemicals 

for cleaning the non-metallic parts of the tool. These 
chemicals may weaken the materials used in these parts. 
Use a cloth dampened only with water and mild soap. 
Never let any liquid get inside the tool; never immerse any 
part of the tool into a liquid.

Optional Accessories

WARNING:

 Since accessories, other than those offered 

by 

D

e

WALT

, have not been tested with this product, use 

of such accessories with this tool could be hazardous. 
To reduce the risk of injury, only 

D

e

WALT

 recommended 

accessories should be used with this product.