background image

5

WARNING: RISk TO BREATHING (ASPHyxIATION) 

WhaT can haPPen

hoW To PreVenT IT

• Some paints, coatings and

solvents may cause lung

damage, and burns if inhaled

or allowed to come into

contact with skin or eyes.

• Use a NIOSH approved mask

or respirator and protective

clothing designed for use with

your specific application and

spray materials. Some masks

provide only limited protection

against toxic materials and

harmful paint solvent. Consult

with a Safety Expert or

Industrial Hygienist if

uncertain about your

equipment or materials.

WARNING: RISk Of INJECTION

WhaT can haPPen

hoW To PreVenT IT

• Spray guns operate at

pressures and velocities high

enough to penetrate human

and animal flesh, which could

result in amputation or other

serious injury.
! See a physician immediately !

• Never place hands in

front of nozzle.

•  Direct spray away from

self and others. 

• Seek immediate medical

attention if direct spray contacts

exposed body parts.

WARNING: RISk fROm flyING OBJECTS

WhaT can haPPen

hoW To PreVenT IT

• Certain parts are under

pressure whenever the gun

is connected to a pressurized

air line. These parts may be

propelled if the gun

is disassembled.

• Disconnect the gun from

the air line, or completely

depressurize the air line

whenever the gun is to

be disassembled.

• Compressed air may propel

dirt, metal shavings, etc. 

and possibly cause an injury.

• Never point any nozzle or

sprayer toward a person or part

of the body.

• Always wear 

anSI Z87.1 can/

cSa Z94.3 approved safety

glasses with side shields. 

• Prolonged exposure

to air spray can result in

permanent damage

to hearing.

• Always wear hearing protection

when operating spray equipment. 

Summary of Contents for DWMT70778












Reviews: