background image

Section 2 Direct Excitation (Brush Type)

Diagnostic Repair Manual

15

AC Diagnostic Tests

Introduction

The Diagnostic Tests in this chapter may be performed in
conjunction with the 

Troubleshooting Flow Charts

. Test

numbers in this chapter correspond to numbered tests in
the flow charts.

NOTE: 

Test  procedures  in  this  manual  are  not

necessarily the only methods for diagnosing the condition
of  components  and  circuits.  All  possible  methods  that
might  be  used  for  system  diagnosis  have  not  been
evaluated.  If  any  diagnostic  method  is  used  other  than
the method presented in this manual, the technician must
be sure that neither his personal safety, nor the product's
safety,  will  be  endangered  by  the  procedure  or  method
that has been selected.

NOTE: 

For graphics of different configurations of stators

and  the  wire  numbers  associated  with  different
components,  see  appropriate  wiring  diagrams  and
schematics for the generator.

Test 1 – Check No-Load Voltage and 

Frequency

Procedure

1.

Disconnect  or  turn  OFF  all  electrical  loads
connected to the generator.

2.

Set  digital  multimeter  (DMM)  to  measure  AC
voltage.

3.

Reset all circuit breakers to ON.

4.

Start engine and let stabilize and warm up.

5.

See 

Figure 1-5

.  Place  meter  test  leads  into  an

outlet.

Figure 1-5. DMM Test Leads Connected to a 240 VAC 

Receptacle

6.

Read AC voltage.

7.

Connect  an AC  frequency  meter  as  described  in
Step 5.

8.

Read AC frequency.

Results

Refer to flow chart.

Test 2 – Check Main Circuit Breaker

Procedure

The generator has circuit breakers located on the control
panel.  If  outlets  are  not  receiving  power,  make  sure
breakers are set to ON or “Closed”.
If a breaker is suspected to have failed, test as follows:

1.

Set DMM to measure resistance.

2.

With  generator  shut  down,  disconnect  all  wires
from suspected circuit breaker terminals to prevent
interaction.

3.

See 

Figure 1-6

.  With  the  generator  shut  down,

connect one meter test lead to one terminal of the
breaker and the other meter test lead to the other
terminal. 

4.

Set  breaker  to  ON  or  “Closed”.  The  meter  should
read CONTINUITY.

5.

Set  breaker  to  OFF  or  “Open”.  The  meter  should
indicate INFINITY.

Figure 1-6.  20/30 Amp Breaker Test Points

Results

1.

If circuit breaker tests good, refer to flow chart.

2.

If breaker tests bad, replace.

Test 3 – Check Continuity of 

Receptacle Panel

General Theory

Continuity  of  the  receptacle  panel  is  important  as  it
recognizes  the  receptacle  has  continuity  through  the
wiring  and  is  physically  connected  to  the  stator.  Most
stator winding values are between 0.01 and 0.02 Ohms
of  resistance.  If  a  higher  than  normal  ohm  reading  is
shown,  a  poor  connection  could  be  the  problem
preventing that receptacle from receiving power.

240

No Load Voltage

No Load Frequency

223.2 – 256.8 VAC

62.5 – 62.0 Hz

00.01

C.B.

20/30A

Summary of Contents for DXGN14000

























































Reviews: