background image

Section 3 Engine Diagnostic Tests

Diagnostic Repair Manual

33

1.

See 

Figure 1-10

Loosen rocker arm jam nut. Turn

pivot  ball  stud  while  checking  clearance  between
rocker arm and valve stem with a feeler gauge.

Figure 1-10. Adjusting Valve Clearance

2.

See 

Figure 1-11

When clearance is correct, hold

pivot ball stud with Allen wrench and tighten rocker
arm  jam  nut  to  specified  torque  with  a  crow  foot
wrench.  After  tightening  jam  nut,  recheck  valve
clearance to make sure it did not change.

Rocker Arm Jam Nut ft-lbs
4209 to 12

Figure 1-11. Tightening Jam Nut

Install Rocker Arm Cover

1.

Use a new rocker arm cover gasket. Install rocker
arm cover and retain with four screws.

Results

Adjust  valves  to  specification  and  test.  If  problem
continues, refer to flow chart.

Test 25 – Check Engine / Cylinder 

Leak Down Test / Compression Test

General Theory

Most  engine  problems  may  be  classified  as  one,  or  a
combination of the following:

Will not start

Starts hard

Lack power

Runs rough

Vibration

Overheating

High oil consumption

General Theory

The  Cylinder  Leak  Down  Tester  (Figure  44)  checks
sealing (compression) ability of engine by measuring air
leakage  from  combustion  chamber.  Compression  loss
can  present many different  symptoms. This test detects
the  section  of  the  engine  where  the  fault  lies  before
disassembling the engine.

Procedure

1.

Remove spark plug.

2.

Gain access to flywheel. Remove valve cover.

3.

Rotate  engine  crankshaft  until  the  piston  reaches
top  dead  center  (TDC).  Both  valves  should  be
closed.

4.

Lock flywheel at top dead center.

5.

Attach  cylinder  leak  down  tester  adapter  to  spark
plug hole.

6.

Connect an air source of at least 90 psi to the leak
down tester.

7.

Adjust regulated pressure on gauge to 80 psi.

8.

Read  right  hand  gauge  on  tester  for  cylinder
pressure.  20  percent  leakage  is  normally
acceptable.  Use  good  judgment, and  listen  for  air
escaping  at  carburetor,  exhaust,  and  crankcase
breather. This determines where the fault lies.

Figure 1-12. Spark Tester

Results

Air escapes at carburetor – check intake valve.

Air  escapes  through  exhaust  –  check  exhaust
valve.

Air escapes through breather – check piston rings.

Air  escapes  from  cylinder  head  –  replace  head
gasket.

000258

Summary of Contents for DXGN14000

























































Reviews: