background image

Section 3 Engine Diagnostic Tests

34

Diagnostic Repair Manual

Check Compression

To check engine compression, remove spark plug. Insert
an  automotive  type  compression  gauge  into  the  spark
plug  hole.  Crank  engine  until  there  is  no  further  in
pressure.  The  highest  reading  obtained  is  engine
compression pressure. 

Minimum  Allowable  Compression  Pressure  Cold
Engine – 60 psi

 

If compression is poor, look the following causes: 

Loose cylinder head bolts

Failed cylinder head gasket

Burned valves or valve seats

Insufficient valve clearance

Warped cylinder head

Warped valve stem

Worn or broken piston ring(s)

Worn or damaged cylinder bore

Broken connecting rod

Worn valve seats or valves

Worn valve guides

NOTE: 

Refer  to  Engine  Service  Manual  Part  Number

0C1103A  for  further  engine  service  information  on  the
engine.

Test 26 – Check Ignition Coil

General Theory

The ignition system used on GH-220 engines is a solid-
state (breakerless) type. The system utilizes a magnet on
the engine flywheel to induce a relatively low voltage into
an  ignition  coil  assembly.  Ignition  coil  internal
components  increases  voltage  and  delivers  the  high
voltage across spark plug gap.
The  ignition  coil  houses  a  solid-state  circuit  board
controlling ignition timing. Timing is fixed, air gap is non-
adjustable, and spark advance is automatic.
Major  components  of  the  ignition  system  include  (a)
ignition  coil  assembly,  (b)  spark  plug,  and  (c)  engine
flywheel.
Solid-state components encapsulated in ignition coil are
not accessible and cannot be serviced. If coil is defective,
replace  assembly.  The  air  gap  between  the  coil  and
flywheel magnet is fixed and non-adjustable. 
See 

Figure 1-13

The ignition coil assembly consists of

(a) ignition coil, (b) spark plug high tension lead, and (c)
spark plug boot.

Figure 1-13. Ignition Coil

Procedure

1.

Disconnect Wire 18 at bullet connector and repeat
Test 20.

2.

If unit produces spark, a short to ground exists on
Wire 18 between the Ignition Coil and RUN-STOP
switch.

3.

If unit still failed to produce spark, proceed to Step
4.

4.

Set  a  DMM  to  measure  resistance.  Connect
negative (-) test lead to Wire 18, going to the coil.
Connect  positive  (+)  test  lead  to  frame  ground.
Approximately 1.5 kΩ should be measured.

5.

Set  a  DMM  to  measure  resistance.  Disconnect
high  tension  lead  from  spark  plug.  Connect  one
test  lead  to  high  tension  lead.  Connect  other  test
lead to frame ground. Approximately 16 kΩ should
be measured.

Results

1.

If unit was able to produce spark after disconnect-
ing Wire 18, a short to ground or a faulty switch is
supplying  Wire  18  with  a  ground  inhibiting  the
engine from producing spark.

2.

If  Ignition  Coil  fails  Step  4  or  Step  5  by  a  high
margin, replace Ignition Coil.

3.

If coil passes Step 4 and Step 5 but there is still no
spark, replace ignition coil. 

NOTE: 

Before  replacing  ignition  coil,  check  flywheel

magnet.

Checking Flywheel Magnet

The  flywheel  magnet  rarely  loses  magnetism.  To
determine if a magnet is be defective, perform this test:

1.

Place flywheel on a wooden surface. 

2.

Hold a screwdriver at the utmost end of handle with
its point down.

3.

Move tip of screwdriver to about 3/4 inch (19mm)
from  magnet.  The  screwdriver  blade  should  be
pulled in against magnet.

001696

Summary of Contents for DXGN14000

























































Reviews: