31
EnGLIsH
To Install the Battery Pack into the Tool
1. Align the battery pack
19
with the rails inside the tool
(Fig. C).
2. Slide it into the tool until the battery pack is firmly seated
and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button
18
and firmly pull the battery pack
out of the tool handle (Fig. D).
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. E)
Some
D
e
WALT
battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button
21
. A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOtE:
The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Removing blower from box (Fig. A)
nOtE:
The blower and joystick tube assembly are attached
when shipped. Trying to pull one side out without the other
may result in damage to the cable
11
.
1. Grab the blower handle
15
and the joystick
1
and
removing simultaniously.
2. Cut the plastic zip tie that is tethering the joystick to
the blower.
3. Remove the rest of the parts and assemble as
instructed below.
Assembly (Fig. A, F –M)
CAUTION: Ensure the battery-selection switch is
in the center "OFF" position to prevent the blower
from actuating and the battery is removed before
attaching or removing the tubes. The tubes must be
fully assembled before use.
Tube Assembly
attaching Flexible tube to elbow tube (Fig. a, F, G)
1. Remove the tube clamp with cable clip
10
from the flexible
tube
7
. Note the orientation of the clamp for when it
is reattached.
2. Slide the flexible tube over the elbow tube
8
as shown in
figure F.
3. Keeping the clamp in the same orientation as it was before
removing it from the flexible tube, pull open the clamp
with cable clip and wrap it around the flexible tube where it
attaches to the elbow tube as shown in figure G.
4. Slide the clamp bolt
22
through the clamp. Thread the hex
nut
23
onto the clamp bolt by hand.
5. Using the hex wrench
20
, tighten the bolt until the clamp
holds the flexible tube securely to the collar and joystick
tube.
DO nOt OVERtIGHtEn.
Overtightening the clamp
could result in damage to the tool and will restrict the
movement of the joystick tube
6
.
attaching flexible tube to joystick tube (Fig. a, G, H)
1. Insert the tube collar
24
at the end of the joystick tube
6
into one end of the flexible tube
7
as shown in figure H.
2. Pull open the tube clamp
9
and wrap it around the flexible
tube where it overlaps the tube collar.
3. Slide the clamp bolt
22
through the clamp. Thread the hex
nut
23
onto the clamp bolt by hand.
4. Using the hex wrench
20
, tighten the bolt until the clamp
holds the flexible tube securely to the collar and joystick
tube.
DO nOt OVERtIGHtEn.
Overtightening the clamp
could result in damage to the tool.
attaching Lower tube (Fig. I)
1. Line up the channels
25
of the lower tube
5
with the
nubs
26
on the joystick tube
6
as shown in figure I.
2. Slide the lower tube
5
onto the joystick tube
6
.
3. Firmly twist the lower tube to lock the nub completely
into one of the two recesses of the lower tube. The two
recesses allow you to set the tube longer or shorter,
depending on the length desired. Ensure the lower tube is
securely attached.
adjusting harness (Fig. a, J–k)
1. Place the shoulder straps
12
over your shoulders.
2. Pull the adjustment straps
13
down until the backplate
14
is firm against your back (figure J).
3. Snap the buckle
16
together and adjust so it fits firmly
across your chest as shown in figure K.
adjusting joystick (Fig. L - M)
1. Slide the joystick
1
up and down the tube until it is in a
comfortable use position as shown in figure L.
2. Tighten the wingnut
27
until the joystick is held firmly in
position. Do not overtighten. Overtightening the joystick
could result in damage to the tool.
3. Secure the cable
11
by pushing it into the cable clip
28
located on the tube clamp with cable clip
10
as shown in
figure M.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Summary of Contents for Pro Landscaping DCM587
