DeWalt XR FLEXVOLT LI-ION DCC1054 Original Instructions Manual Download

Page: 38 / 172

EngLIsH

WARNING:

Risk of Bursting.

Water will condense in the

air tank. If not drained, water will corrode and weaken the
air tank causing a risk of air tank rupture.

NOTICE: Risk of Property Damage.

Drain water from

air tank may contain oil and rust which can cause stains.

1. Set the Auto On/Off switch

to "Off".

2. Remove the battery.
3. Turn the One‑Turn regulator

counterclockwise to set the

outlet pressure to zero.

4. Remove the air tool or accessory.

WARNING:

When loosening the hose coupling from the

quick-connect coupler

, the coupling piece of the hose

must be held by hand in order to avoid injuries caused by
the recoiling hose.

5. Place a suitable container under the drain valve to

catch discharge.

6. Pull ring on safety valve

allowing air to bleed from the

tank until tank pressure is approximately 1.4 BAR. Release
safety valve ring.

7. Drain water from air tank by opening drain valve

bottom of tank.

8. After the water has been drained, close the drain valve. The

air compressor can now be stored.

nOTE:

If drain valve is blocked, release all air pressure by

connecting a tool to the airline and operating it until tank
pressure is zero BAR and contact the

WALT

service centre.

Storage

Before you store the air compressor, make sure you do
the following:

1. Review the

Maintenance

section and perform scheduled

maintenance as necessary.

2. Always toggle Auto On/Off Switch to "Off" and remove

battery. Drain water from air tank. Refer to

To Drain Tank

under

Maintenance

WARNING: Water will condense in the air tank. If not
drained, water will corrode and weaken the air tank
causing a risk of air tank rupture.

3. Store the air compressor in a clean and dry location.
4. Make sure the air compressor is secured in such a way that it

cannot be started up again by any unauthorized person.

5. Frost destroys the pump and accessories as both always

contain water. If there is a risk of danger of frost, store in
frost‑free conditions.

Cleaning

WARNING:

Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING:

Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.

Optional Accessories

WARNING:

Since accessories, other than those offered

WALT

, have not been tested with this product, use

of such accessories with this tool could be hazardous.
To reduce the risk of injury, only

WALT

recommended

accessories should be used with this product.

Consult your dealer for further information on the
appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at

www.2helpU.com

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from

the tool.

• Li‑Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be
recycled or disposed of properly.

GLOSSARY

cut-In Pressure:

While the motor is off, air tank pressure drops

when accessory is used. When the tank pressure drops to a
certain low level the motor will restart automatically. The low
pressure at which the motor automatically restarts is called

cut-in

pressure.

cut-Out Pressure:

When an air compressor is turned on and

begins to run, air pressure in the air tank begins to build. It
builds to a certain high pressure before the motor automatically
shuts off, protecting your air tank from pressure higher than
its capacity. The high pressure at which the motor shuts off is
called

cut-out

pressure.

Duty cycle:

This air compressor pump is capable of running

continuously. However, to prolong the life of your air
compressor, it is recommended that a 50%–75% average duty
cycle be maintained; that is, the air compressor pump should
not run more than 30–45 minutes in any given hour.