background image

 

 

Page 9                                                 

Printing version 2.6

 •JUL2017

 

 

 

3  Specifications 

Analog inputs 

 

Number of channels 

Inputs 

Voltage, bridge (IEPE, temperature 
with adapters) 

ADC type 

24 bit sigma delta with  
anti-aliasing filter (see section ADC) 

Sampling rate 

simultaneous 200kS/sec sampling 
rate 

Input type 

Differential 

Input ranges 

±10V, ±1V, ±100mV, ±10mV 

Sensor supply 

12V, 400mA sensor supply 
±5V ±0.1% bridge sensor supply 

Overvoltage protection 

±70V input protection 

Dynamic range 

107dB@ ±10V range 

DC accuracy  10 V range 

0,05% of value +1 mV 

                       1 V range 

0,05% of value +0.2 mV 

                       100 mV range  0,05% of value +0.1 mV 
                       10 mV range 

0,05% of value +0.1 mV 

Input impedance 

20M

Ω||47pF(differential)

 

10M

Ω||33pF(common mode)

 

CMRR 

>80dB (see section CMRR) 

Maximum common mode 
voltage 

 
±13V 

Signal to noise  
   0.1kS/s to 51.2kS/s 
   51.2ks/s to 102.4kS/s 
   102.4kS/s to 200kS/s 

 
105dB 
100dB 
75dB 

Channel-to-Channel Phase 
Mismatch 

<0.1deg @5kHz 

Phase-to-Phase Mismatch 

-0.6deg @1kHz 

 
 
 
 
 

Summary of Contents for DEWE-43






































Reviews: