DFA SqwidNET Visio Tamper Installation Manual Download | Manualshive

Page: 3 / 13

background image

The Visio Tamper device is a compact, robust and waterproof
device that sends an alert over the Sigfox network if the
orientation of the device changes. This makes it ideal for
installation on the inside of manhole covers, to monitor
unauthorised access.

Fig. 1.1 Visio Tamper device

1. Visio Tamper Device

1

«
1
2
3
4
5
...
»

Summary of Contents for SqwidNET Visio Tamper














Reviews:

No comments

Related manuals for SqwidNET Visio Tamper

Brand: nedis Pages: 68

Brand: Fike Pages: 4

Brand: Perel Pages: 20

Brand: CommBox Pages: 4

Brand: NAVAC Pages: 4

Brand: Velleman Pages: 58

Brand: ICP DAS USA Pages: 96

Brand: Tasco Pages: 24

360 GROUND FINDER Series

Brand: S&C Pages: 3

Brand: Eaton Pages: 3

Mighty DomeColor Dome Camera Series

Brand: Vitek Pages: 28

Brand: Feig Electronic Pages: 12

Brand: ALC Pages: 55

CGAS-A-VLT-NH3-S

Brand: Critical Environment Technologies Pages: 20

Brand: First Alert Pages: 44

Brand: Inter-m Pages: 36

Brand: Spinlock Pages: 7

Brand: Vivotek Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands