www.dfi .com
9
Chapter 2 Hardware Installation
Chapter 2
Chapter 2 - Hardware Installation
Board Layout
2
9
10
1
Front Audio
S/PDIF
1
Buzzer
PCI 1
PCI 2
PCI 3
PCI 4
PCIe x16
CPU Fan
1
1
2
5
6
1
2
5
6
1
2
9
10
USB 2-3
1
1
Clear CMOS Data (JP9)
1
Mini PCIe Power
Select (JP16)
1
COM2
COM1
Standby
Power LED
1
Power-on
Select (JP10)
1
1
1
12 10
3
1
Mini PCIe Signal
Select (JP15/JP18)
12 10
3
1
SATA 2.0
SATA 3.0
Nuvoton
NCT6102D
(JP14)
(JP3)
DIO
Socket LGA1150
PCIe x1
PCIe x4 (x1 Signal)
USB 2-3 Power
Select (JP8)
1
2
5
6
1
2
5
6
(JP2)
(JP11)
(JP4)
12
24
1
2
19
2
1
26
25
Parallel
1
2
10
9
1
2
10
9
COM4
COM3
1
2
10
9
1
2
10
9
COM5 COM6
System Fan 1
1
SPI Flash
BIOS
1
1
1
ATX
Power
Chassis
intrusion
1
1
12
2
11
+12V
Power
1 2
1112
LAN 1
USB 0-1
USB 3.0
USB 2.0
System Fan 2
1
Battery
Front
Panel
1
SATA 0
SATA 1
SATA 4
SATA 5
DDR3_1
DDR3_3
US
USB
SB
SB 2
B 2
2
U
U
.0
0
.0
PS/2 KB/MS
USB 8-9
Realtek
ALC886
ITE
IT8892E
Line-in
Line-out
Mic-in
DVI-I
HDMI
1
1
1
1
USB 0-1 Power
Select (JP5)
Mini PCIe
USB 4-5 Power
Select (JP6)
(JP1)
(JP12)
(JP13) (JP7)
ASMedia
ASM1442
ASMedia
ASM1442
Intel
WGI210AT
ISL95820
SATA DOM Power
Select (JP17)
Intel
H81
Intel
WGI217LM
Note:
SATA5 supports SATA DOM.
PS/2 KB/MS Power Select (JP1)
USB 8-9 Power Select (JP4)
COM1 RS232/422/485
Select
COM2 RS232/422/485
Select
COM1 RS232/Power
Select
COM2 RS232/Power
Select
(JP2)
(JP11)
(JP3)
(JP14)
1
13
1 5
4 8
USB 2.0
LPC
USB 4-5
USB 2.0
DIO Power Select
(JP13)
DIO 11/13/15/17
Output State (JP7)
DIO 3/5/7/9
Output State (JP12)
LAN 2
USB 2.0
USB 2.0
System Memory
Standby
Power LED
Features
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Important:
When the Standby Power LED lights red, it indicates that there is power on the
system board. Power-off the PC then unplug the power cord prior to installing any de-
vices. Failure to do so will cause severe damage to the motherboard and components.
Rear I/O
Onboard I/O
Storage
Expansion
DDR3-3
DDR3-1
• Two
240-pin
DDR3 DIMM sockets
• Supports
DDR3 1333/1600MHz
•
Supports dual channel memory interface
•
Supports up to 16GB system memory
•
HD630-H81B has LAN1 only.
•
HD630-H81C: 6 COM (COM1 to COM6).
HD630-H81B/D: 2 COM (COM1 and COM2).
