PPC2+™ Operation and Maintenance Manual
Page 11
©2001 DH Instruments, Inc.
2.3.4
CONNECTING TO A PRESSURE SUPPLY (SUPPLY PORT)
Using a pressure connecting hose of appropriate pressure rating, connect the pressure supply
to the SUPPLY connection on the rear panel of PPC2+. The PPC2+ SUPPLY connection is
1/8 in. NPT female.
The supply pressure should be equal to the maximum PPC2+ range +10 %. Lower gas
pressure sources can be used but should exceed the maximum desired test output pressure
by 10 to 20 %.
8O`O\ MYXXOM^ K Z\O]]_\O ]_ZZVc Q\OK^O\ ^RKX Y`O\ ^RO WKbSW_W \KXQO 2 YP ^RO
::-WYNOVcY_K\O_]SXQ
2.3.5
CONNECTING A VACUUM PUMP (EXHAUST PORT)
For PPC2+ to set pressures under atmosphere and/or to reliably set pressure under
3 psi (20 kPa) gauge other than zero gauge, a vacuum pump must be connected to the
EXHAUST port.
8O`O\MYXXOM^KZ\O]]_\O]_ZZVc^YY\ZV_Q^RO::-/B2+?=>ZY\^
>Y K`YSN L_SVNSXQ _Z Z\O]]_\O YX ^RO /B2+?=> ZY\^ KXNY\ ^RO `KM__W Z_WZ ^RO `KM__W
]Y_\MO]RY_VNOS^RO\LOMYX^SX_Y_]Vc98Y\]RY_VNLcZK]]^YK^WY]ZRO\OaROX^RO`KM__W
]Y_\MOS]900>RS]S]LOMK_]OaROXK]_ZZVcZ\O]]_\OS]KZZVSON^Y^RO::-=?::6CZY\^
KXN^RO::-S]89>SX^RO`OX^98MYXNS^SYX^RO\OS]KMYX]^KX^QK]ObRK_]^^R\Y_QR^RO
::-/B2+?=>ZY\^^YaRSMR^RO`KM__W]Y_\MOaSVVLOMYXXOM^ON
>YK]]_\OYZ^SW_WZ\O]]_\OMYX^\YVaROXMRKXQSXQ^ROZ\O]]_\OKZZVSON^Y^RO/B2+?=>ZY\^
P\YW`KM__W^YK^WY]ZRO\OY\`SMO`O\]KLO]_\O^YMRKXQO^ROMYX^\YV\OPO\OXMO]O^^SXQSP
^RO]O^^SXQS]89>SX+?>9WYNO]OO=OM^SYX
2.3.6
CONNECTING TO THE DEVICE UNDER TEST (TEST AND TEST(-) PORTS)
If you are using a SPLT, see Section 2.3.6.1 before proceeding to connect the device
under test.
Using a pressure connecting hose of appropriate pressure rating, connect the device or
system to be tested to the TEST port of the PPC2+. The PPC2+ TEST connection is
1/4 in. NPT female.
If PPC2+ is equipped with a gauge RPT (GXXXX), it has a TEST port and a TEST(-) port.
The TEST(-) port is connected to the low side of the gauge RPT. This connection is normally
left open to atmosphere. It can also be connected to the low side of a differential device that
is being calibrated or tested. With very low pressure devices, this will enhance the calibration
results by helping assure that PPC2+ and device under test reference ports are at the
same pressure.
Summary of Contents for PPC2+
