background image

STORAGE:

Always turn off the marker, remove the hopper/feeder, all paintballs and propel-
lant source and place it in a secure location where it cannot be accessed by
unauthorized persons. 

TROUBLE SHOOTING GUIDE:

Symptom

Cause

Cure

Does not Fire

Not Cocked

Cock the Bolt Pull
Pin (28A) to the rear.

Not On

Turn Switch “On”

Bad Battery

Replace Battery

Out of Gas

Refill or Replace 
Propellant Source

Leaks air down Barrel

Bad Cup Seal (7)

Replace Cup Seal (7)

Leaks air from

Bad Bottle O-Ring

Replace Bottle O-Ring

ASA/Bottle

Interface

Does not Re-cock

Low on Gas

Refill or Replace
Propellant Source

Goes “Full Auto”

Sear not catching

Tighten Grip Frame
Screws (21)

Low on Gas

Refill or Replace
Propellant Source

Bad Striker O-Ring

Replace Multi-use
O-Ring (16) located
on front of Striker

Excessive Ball

Low Quality Paintballs

Use better Paintballs

Breakage

Such as Diablo Brand

Ball Chopping

Use motorized feeder
Such as Diablo TSA

When in doubt, thoroughly clean and lubricate the marker.
Many marker function problems are caused by excessive
dirt or lack of lubrication.

11.

DiabloMongooseManInside2.qxd  10/14/04  2:03 PM  Page 11

Summary of Contents for MONGOOSE















Reviews: