Installing the Dialogic®
Brooktrout® TR1034 BRI
PCI Fax Board
Part Number: 931-106-05
The Dialogic® Brooktrout® TR1034 BRI
(Basic Rate Interface ISDN) PCI boards
(“TR1034” or “TR1034 fax board(s)”)are half-sized,
single-slot PCI-bus compatible fax boards. They
provide the following:
On-board BRI connections
V.34 (33.6 Kbps) fax transmission speeds
Up to four fax and voice channels per board
The TR1034 BRI PCI Series boards can be used in
either 3.3V or 5V bus (signaling) slots.
You need a fax or voice application to use a
TR1034 BRI Fax Board. Dialogic does not provide
the application or a driver for this board. A driver
comes with the application that you purchase.
This installation guide provides information about:
System Requirements (including telephone
service)
Setting Termination Jumpers for the BRI Line
Using the Dialogic® Brooktrout® TR1034 BRI
Fax Board
System Requirements
This board must be installed in an enclosure that
meets the following specifications:
A Pentium or later host processor
A PCI bus slot that runs at least 33 MHz and is
32 or 64 bits wide. See
for
more information.
Temperature: 0 C - 50 C
Humidity: 10% - 95% (non-condensing)
Power Requirements:
The following is also required:
Telephone service: BRI interface
Setting the Module Number
Set each board to a unique module number to easily
identify the resources associated with a specific board
in a multi-board system.
Use the SW-1 rotary switch (Figure 1) to set a unique
module number for each Dialogic® Brooktrout® fax
board. See Figure 5 for the switch location. Select a
number from 2 - F on the rotary switch. Settings 0 and
1 are reserved and cannot be used.
Figure 1. Rotary Switch (SW-1)
Setting Termination Jumpers
for the BRI Line
Before installing your board, set termination for the
BRI line if necessary. See Figure 5 for the location of
the termination switches.
Set jumpers as follows (See Figure 2 for details):
Figure 2. Termination Jumpers
When the jumpers are removed from both
switches for the appropriate port, there is no
termination.
When jumpers are present, the lines are
terminated with 100
ohms (this is how the boards
are shipped)
.
Dialogic does not support any configuration
except the two illustrated in Figure 2.
Installing the Fax Board
To install your board:
1.
Turn off your PC and remove the cover.
2.
If the system has a PCI expansion hold-down bar,
remove it.
3.
Locate a free PCI bus slot and remove the slot
cover.
4.
Carefully align the board with the slot and firmly
seat the board into the slot.
5.
Tighten the mounting bracket screw to secure the
board to the chassis.
6.
Replace the cover.
7.
Turn on your computer.
Note:
Dialogic® Brooktrout® fax boards should not be present in
the computer during the installation of any operating
system. The operating system might misinterpret the board
as being some other device, with unpredictable
consequences.
Recognizing PCI Slots
The PCI connectors in the computer chassis usually
appear as white slots. The TR1034 BRI Fax Board
has a PCI board edge connector. It can be inserted into
any of the PCI slots shown in Figure 3.
Figure 3. PCI Slots
Connecting the Phone Service
The appropriate telephone service and hookups must
be installed at your site in order to connect to
telephone service. The following table shows the
channel/port relationship:
Use the cable supplied with the board. Do the
following to connect your board to BRI service:
1.
Plug one end of the cable into the telephone
connector on the board.
Connect to Port A for channels 0 and 1 or to
Port B for channels 2 and 3 (see Figure 5 to
locate ports).
2.
Plug the other end into the wall connector for
your BRI service.
Note:
Port B is not present on the TR1034 BRI single port version.
Board
+5 V +3.3 V +12 V -12 V Total Power
Single channel
0.8A 0A
0A
0A
4.0 W
Dual channel
0.9A 0A
0A
0A
4.5 W
Caution: A small amount of static electricity can
destroy the sensitive components on your board.
To prevent static damage, always connect yourself
to ground using a ground strap before touching a
circuit board. Handle boards only by the edges or
metal mounting brackets and transport boards in
an anti-static bag.
Warning: When installing the board, be sure that
the mounting bracket is securely fastened to the
chassis and the chassis is plugged into a
grounded three prong plug. Improper chassis or
bracket grounding can result in harmful or fatal
electrical shock as well as component damage.
Jumper is in place
(ISDN BRI line is terminated)
Jumper is removed
(ISDN BRI line is not terminated)
Channel
Number
RJ-45 Port
Type of
Service
0
1
2
3
A
A
B
B
BRI S/T
BRI S/T
BRI S/T
BRI S/T
5V 64-Bit Connector
3.3V 32-Bit Connector
Insert the connector into any of these slots.
3.3V 64-Bit Connector
5V 32-Bit Connector
Universal PCI Board Edge Connector
