background image

 

Element Series Manual 

 

Page | 1  

 

Element (ELE-800, ELE-1600, ELE-1800, ELE-2400, ELE-
4800, ELE-7200) Manual 

Inspect the packaging

 of the equipment to confirm that nothing was damaged during 

shipping.  

Remove the system from the packaging

. Make sure everything is included and without 

damage. Below is a checklist of the major components to check. The system will 
already be assembled and should arrive in one piece. 

_____ 1) Pump 
_____ 2) Front Panel 
_____ 3) Membrane Housing(s) 
_____ 4) Filter Housing 

Call Diamond H2O right away if anything is missing. Contact the freight company 

immediately

 if anything is damaged. Diamond H2O will not be liable for any damage received after shipping. 

Packaged By: ___________________________________              Date: _______________ 
 
Received By:  ___________________________________  

Date: _______________ 

Warnings 

1.

 

System produces Corrosive Water. 

The element produces water with very low Total Dissolved Solids (TDS) and is 

corrosive

Product/Permeate water should not be exposed to metal piping like brass, copper, or steel. Systems 
installed on metallic plumbing must use Pro Products LLC Neutra 7 for protection from corrosion. 

2.

 

System produces Concentrated Water. 

The element produces water with very high TDS which can be dangerous. Concentrate/Reject water will 
contain a higher concentration of most contaminants than the source water and should not be used as 
drinking water.  

3.

 

120/240V present in control box 

To reduce the risk of electrical shock, the incoming power supply must include a protective earth ground.

 

4.

 

Pump will boost pressure by approximately 150psi.  

5.

 

Use on board TDS monitor as a secondary reference only. 

TDS is a general indication of all the ions present in water. A reduction in TDS does not necessarily mean a 
reduction in a specific contaminant. Testing for specific contaminants at least annually is recommended.  
 

Contact 

TG

 Analytical Labs

 

with any questions on testing coliform 

bacteria, nitrate, arsenic

, and more. 

Email: 

info@tgalabs.com

          Phone: 920-757-1355          Fax: 920-757-5819 

Summary of Contents for Element ELE-1600













Reviews: