background image

 

 

 

DS-MPE-CAN2L User Manual Rev A. 

www.diamondsystems.com

  

 

    

 

Page 16 

// Set 500k Baud rate for CAN#0 

ret_val = set_baudrate(

can0_fd

, CAN_SPEED_500K ) ; 

if ( ret_val < 0 ) 

printf("Error while setting the baud rate \n") ; 

exit(0) ; 

// Set 500k Baud rate for CAN#1 

ret_val = set_baudrate(

can1_fd

, CAN_SPEED_500K ) ; 

if ( ret_val < 0 ) 

printf("Error while setting the baud rate \n") ; 

      exit(0) ; 

Use below macros for setting the different baud rates. These macros can also be found in can.h file.  

 

CAN_SPEED_1M  

CAN_SPEED_800K 

CAN_SPEED_500K 

CAN_SPEED_250K 

CAN_SPEED_125K 

CAN_SPEED_100K 

CAN_SPEED_50K 

CAN_SPEED_20K 

 

CAN Transmit & Receive:  

can_tx() & can_rx() : 

These function will be used to Transmit and Receive the CAN messages respectively.  

 

CAN Transmit Prototype.  

int can_tx( int can_fd, unsigned char  msgType, unsigned int can_id, int len,unsigned char *data) ; 

 

Assign the appropriate values, before calling the can_tx function. 

 

can0_fd : CAN descriptor, return value from init_can0() function 

msgType = MSG_STANDARD ; //  or MSG_EXTENDED .  

can_id = 0x12 ; // CAN ID, if the msgType is MSG_STANDARD then it should be 11-Bit CAN Message ID  

// if the msgType is MSG_EXTENDED then it should be 29-Bit CAN Message ID 

len = 4 ; // CAN Transmit Data Length  

data : CAN message data.  

data[0] = 0x1A ; 

data[1] = 0xAB ; 

Summary of Contents for DS-MPE-CAN2L




















Reviews: