22
EN
2. GENERAL TECHNICAL FEATURES
2.1. DATA SHEET
Model
Cooling capacity
Voltage
Gas
Cooling pow. Tot. pow. Packed vol.
Gross Weight
3 x 1/1 GN
12 Kg (+3 °C)
8 Kg (-18 °C)
230 V
1N 50 Hz
R404A
645 W
670
0.36 m
3
75 kg
5 x 1/1 GN
18 Kg (+3 °C)
12 Kg (-18 °C)
230 V
1N 50 Hz
R404A
792 W
875
0.59 m
3
103 kg
5 x 1/1 GN
+ 60x40
18 Kg (+3 °C)
12 Kg (-18 °C)
230 V
1N 50 Hz
R404A
792 W
875
0.67 m
3
116 kg
10 x 1/1 GN
+ 60x40
36 Kg (+3 °C)
25 Kg (-18 °C)
230 V
1N 50 Hz
R404A
1486 W
1060
1.16 m
3
170 kg
15 x 1/1 GN
+ 60x40
48 Kg (+3 °C)
32 Kg (-18 °C)
400 V
3N 50 Hz
R404A
2303 W
1360
1.32 m
3
190 kg
3. INSTRUCTIONS FOR THE INSTALLER
Read carefully all the instructions in this manual, because they give important suggestions about the right instal-
lation and use of the appliance.
3.1. CONTROLS AT RECEPTION
The appliance are shipped in appropriate protective packing.
On arrival, check that the appliance has not incurred in transport damage and that it is complete according to
the order. In the event of visible damage immediately note the damage on the transport documents with the
following wording: “
RECEIVED WITH RESERVE FOR EVIDENT DAMAGE OF PACKING
”.
3.2. HANDLING AND PLACING
IMPORTANT
: All the operations indicated below must be performed in respect of the existing safety regulations,
both for the equipment in use and for the operating procedures.
ATTENTION
: Before beginning handling operations ensure that the lifting capacity is enough for the appliance in
question.
Handling with fork lift or similar (A); Insert the forks into the side or back of the wooden pallet supplied with the
appliance, begin lifting checking that the appliance is in stable equilibrium.
When insert the lifting device, pay attention to the power supply cable and the position of the feet.
ATTENTION
: during handling do not tip or turn over.
WARNING
: the respect of the recommendations printed on the outside of the packing is a guarantee of a sound
physical and operating condition of the appliance, all to the advantage of the end-user.
THEREFORE THE FOLLOWING IS RECOMMENDED:
• HANDLE WITH CARE
• KEEP DRY
• STACKING OF OTHER OBJECTS ON THE APPLIANCE MUST BE ABSOLUTELY AVOIDED
• DO NOT COMPRESS SIDEWAYS
• DO NOT TURN UPSIDE DOWN
•
STACKING OF BLAST CHILLERS IS PERMITTED: READ CAREFULLY THE MAXIMUM PIECES’ NUMBER INDICATED
ON THE EMBALLAGE.
Lift the appliance to separate it from the pallet.
Remove the packing (B) and the protective film avoid using abrasive brushes or other damaging materials for
the appliance’s surfaces (C).
Check that the appliance is perfectly levelled.
Regulate the adjustable feet if necessary. Place the appliance away from heat sources and in a ventilated room.
When using the appliance, never obstruct the air inlet when the appliance in on, so as not to compromise its
performance and safety.
Placing the appliance in a site easy to join, so every type of maintenance, control and repair may be
done easily.
Summary of Contents for BE-910C-DP/DI
