background image

22

shown in Figure 18. Remove the side plugs and
clean the bank under running water.

To clean the internal basin, slide out the overflow
pipe (41) (see Fig. 18). The water that remains will
drain off automatically. Use a sponge to remove any
sediment that may have collected on the bottom of
the basin, and clean the basin.

Remove the stainless steel pump return filter/s, as
shown in Figure 18, and clean under running water.

In addition to the foregoing operations, clean the
ice tray.

Fit all parts back in place, complying with the
demounting instructions in reverse order.

For cleaning, use an ordinary dish-washing
detergent or a solution of water and vinegar. To eli-
minate scaling, use a soft plastic-bristle brush and
a sponge.

Avoid using abrasive detergent or powders, which
may damage the finish.

To obtain a sanitizing effect, repeat the above
cleaning operations using a suitable solution, such
as one of those used for disinfecting baby feeding
bottles.

When the cleaning and/or sanitizing operations
have been completed, rinse the parts thoroughly
with plenty of cold water and eliminate any ice
that may have been produced during the initial
cycles.
Complete sanitizing can only be carried out only
by the Authorized Technical Service Centers,
and must be done regularly depending on the
conditions of use of the appliance, the chemical
and physical features of the water, and after
every period in which the appliance has
remained at a standstill for any length of time.

You are advised to ask your dealer to draw up a
scheduled maintenance contract that will cover
the following:

cleaning the condenser

cleaning the filter located on the water inlet

solenoid valve

cleaning the ice-tray

checking the charge of coolant gas

checking the operating cycle

sanitizing the appliance.

10 PERIODS AT A STANDSTILL

If you do not intend to use the appliance for a certain
period of time, proceed as follows:
·

Switch off the electric power source by means
of the switch fitted during installation, and
remove the plug of the appliance from its socket.

·

Shut off the water supply by turning off the tap
fitted during installation.

·

Carry out all the operations envisaged for
scheduled maintenance of the appliance.

·

Empty out the pump body by blowing
compressed air into the pipe that supplies water
(43) to the sprayer bank.

The Manufacturer declines all liability for any
inaccuracies in this Instruction Manual due to
printing or transcription errors. The Manufacturer
also reserves the right to make any modifications to
the products that may be necessary or useful, also
in the interests of the user, without impairing the
products’ essential features of functionality and
safety.

Summary of Contents for ICE20A
















Reviews: