Digi-Sense 20250-60 User Manual Download | Manualshive

Page: 3 / 16

background image

3

Safety Symbols

Caution refer to this manual before using the

meter.

Dangerous voltages.

Meter is protected throughout by double insulation

or reinforced insulation.

CE Compliance with EN-61010-1
Note: When servicing, use only specified replacement

parts.

Unpacking

Check individual parts against the list of items below. If

anything is missing or damaged, please contact your

instrument supplier immediately.
1. Instrument
2. Test probes
3. Carrying case
4. Six AA batteries
5. User manual

1065DGMAN_20250-60 DS Insulation tester manual.indd 3

8/7/2017 2:09:49 PM

«
1
2
3
4
5
...
»

Summary of Contents for 20250-60

















Reviews:

No comments

Related manuals for 20250-60

Brand: ABB Pages: 18

Brand: R-Tech Pages: 3

Brand: 1010music Pages: 2

Brand: 1010music Pages: 4

Brand: Palmer Pages: 2

Brand: S.R.Smith Pages: 8

Brand: S.R.Smith Pages: 23

NavBoard ZipFlip

Brand: S&S Precision Pages: 6

Brand: GE Pages: 37

MCX-C15 - MusicCAST Network Audio Player

Brand: Yamaha Pages: 114

Brand: ABB Pages: 106

Fresh DFG58D1BSS

Brand: Danby Pages: 11

Portable Vocal Booth Pro Studio Series

Brand: EditorsKeys Pages: 2

Calculite C6P38MHA

Brand: Lightolier Pages: 2

Brand: HEINE Pages: 4

Brand: Trigano Pages: 13

Brand: Harken Industrial Pages: 6

Brand: Rottler Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands