background image

 

ADAT Bridge I/O

 

8

 

if, for example, you have chosen AES/EBU 
as your digital format and are actually re-
ceiving S/PDIF.

 

Slave

 

When continuously lit, this LED indicates 
that the ADAT Bridge I/O master sample 
clock reference is being determined by an 
external device connected to the Slave 
Clock In port on the ADAT Bridge I/O’s rear 
panel, typically another Digidesign Audio 
Interface or an eternal sync peripheral. The 
ADAT Bridge I/O will automatically switch 
to Slave mode when a valid slave clock sig-
nal is connected to its Slave Clock Input 
port and the ADAT Bridge I/O is set for in-
ternal sync in the Pro Tools Hardware 
Setup dialog or Session Setup window.

 

3. Channel 1–2 Input

 

This LED indicates the source of input to 
Pro Tools for channels 1–2 of Group A 
and/or Group B. When the ADAT LED is lit, 
input channels 1–2 in Pro Tools are cur-
rently selected to receive digital input via 
the ADAT Bridge I/O’s optical port. When 
the Digital LED is lit, it indicates that chan-
nels 1–2 in Pro Tools are currently selected 
to receive digital input via its AES/EBU or 
S/PDIF ports. When this is set, ADAT opti-
cal channels 3–8 are still sent to Pro Tools. 
This parameter is set using the Ch 1–2 In-
put pop-up in the Pro Tools Hardware dia-
log or Session Setup window. 

The AES/EBU or S/PDIF inputs can be 
routed to Channels 1–2 of either Group A 
or Group B. This gives you the flexibility to 
set Channel 1–2 to ADAT on Group A, and 
Channel 1–2 input to digital on Group B. 

This allows you to record eight channels 
audio from ADAT on group A, and two 
channels of digital input on Group B. If 
you wish to record a full 16 channels of au-
dio from ADAT, Channel 1–2 input must 
be set to ADAT for both Group A and 
Group B.

 

4. Sample Rate

 

These LEDs indicate the current sample 
rate of Group A and Group B of the ADAT 
Bridge I/O. If these LEDs are flashing, it in-
dicates that the currently selected sample 
rate does not match the sample rate cur-
rently being received by the ADAT Bridge 
I/O.

 

5. Digital Format

 

These LEDs indicate which digital port 
(AES/EBU or S/PDIF) is currently being used 
for digital input on channels 1–2 of Group 
A or Group B. 

Summary of Contents for ADAT Bridge I/O





































































Reviews: