background image

-13-

-12-

CAMERA ADJUSTMENT

CAMERA ADJUSTMENT

This function

 red

uces the ba

ckgr

ou

nd 

noise in a

 low l

uminance e

nv

ironment.

1.Highlight '3DNR' in the main setup menu.

2

. Press the left/right buttons to change setting to OFF/ON

 

OFF - Noise is not reduced

 

ON - Noise is reduced

3. Press ENTER to access the submenu for ON setting.
In the 3DNR submenu you can adjust the noise reduction level values range 
from 0 to 100. Default setting is 60.

Digital Noise Reduction (3D DNR)

Noise levels can be very subtle, and may not be always noticable on adjusting

When adjusting the noise reduction level in 3DNR submenu, remember that the
higher the level set, the more the noise level will be reduced, however this can
have a softening effect on the image.

Notes

  

  �DNR
  LEVEL  

-----|---- ��

  RETURN 

RET

 

 

SETUP
1.  LENS

MANUAL

2.  EXPOSURE
3.  WHITE BAL 

AWB

4.  3DNR 

ON

2. Press ENTER to access the submenu for SPECIAL settings.

1. Highlight 'SPECIAL' in the main setup menu.

SPECIAL. 

SPECIAL

1.  CAM TITLE 

OFF

2.  D-EFFECT
3.  MOTION   

OFF

4.  PRIVACY  

OFF

5.  SYNC 

 

INT

6.  LANGUAGE 

ENG

7.  DEFECT
8.  RETURN   

RET

SETUP
1.  LENS

MANUAL

2.  EXPOSURE
3.  WHITE BAL

ATW

4.  3DNR
5.  SPECIAL
6.  ADJUST

ON

7.  RESET
8.  EXIT
  

CA

M

 TIT

LE

 : If 

you

 en

ter a titl

e, th

e title will appear o

n the monitor.

1. Press left/right buttons to change setting to OFF/ON
 

OFF - No camera title is displayed

 

ON - Camera title is displayed

Summary of Contents for DPB14TLX











Reviews: