background image

1

PS-3650A/PS-3651A Series

Hard Disk Unit

(PS365XA-HD250)

Installation Guide

The PS365XA-HD250 is the hard disk unit 
(HDD unit) for Pro-face’s PS-3650A/PS-
3651A Series (hereafter referred as the "PS-
A") units. This 2.5 inch 250GB hard disk is 
designed to be installed inside the PS-A unit.

Corresponding units: 

PS-3650A/PS-3651A Series

 

(only for the units installing a Serial ATA 
interface)

About the Manual

For the detailed information on PS-A series, 
refer to the following manuals.

• PS-3650A/PS-3651A Series Hard-

ware Manual

The manual can be downloaded from Pro-
face Home Page.

URL

 

http://www.pro-face.com/otasuke/

Safety Cautions

• Be sure to check that the PS-A unit’s 

power is disconnected before installing 
the unit, in order to prevent an electri-
cal shock.

• Do not attempt to modify or open the 

HDD unit, since it can cause a shock or 
fire.

• When installing the HDD unit, be sure 

to read this guide "Installation"  sec-
tion's information completely to insure 
that the unit is correctly installed.

To Prevent Accidents

• Since the HDD unit is a precision instru-

ment, be sure it is neither hit by nor 
pressed strongly against another object. 
After unpacking, be sure the unit is not 
dropped or jolted during installation. Also, 
a PS-A unit built in to a larger unit (i.e. 
operation panel) should be removed and 
packed separately prior to shipping.

• Be sure water, liquids or metal particles are 

not allowed to enter the HDD unit. Any of 
these may cause either a breakdown or an 
electrical shock.

• Do not place or store this unit in a location 

where there is direct sunlight, excessive 
heat, dust or vibration.

• Do not store or operate this unit near chem-

icals, or where there are chemical fumes.

• Do not allow anyone other than Pro-face’s 

own service staff to perform maintenance 
or adjustments to this unit.

• Do not move or shift the PS-A unit while 

the HDD unit is installed and the PS-A 
unit's power is ON.

• Do not use the HDD unit in locations 

where corrosive gasses are present, since 
they can lead to a hard disk breakdown.

• To prevent the data damage, be sure to shut 

down the PS-A unit’s OS according to the 
correct procedure before turning OFF the 
main power.

• To prevent memory leaks, restart the OS 

periodically.

• The hard disk has the lifetime. To use it 

longer by steady operation, read the 
attached “Instructions for Using the Hard 
Disk” carefully.

• In order to extend the lifetime of the hard 

disk, Pro-face recommends you set the 
Windows

®

 [Control panel]-[Performance 

and Maintenance]-[Power Management 
option]-[Turn off hard disks] selection to 
turn the hard disk off when the unit is not 
being operated. A setting of 5 minutes is 
recommended.

Unit Disposal

• When this HDD unit is disposed of, it 

should be done so according to your coun-
try’s regulations for similar types of indus-
trial wastes.

Summary of Contents for PS-3650A series

Page 1: ...emoved and packed separately prior to shipping Be sure water liquids or metal particles are not allowed to enter the HDD unit Any of these may cause either a breakdown or an electrical shock Do not place or store this unit in a location where there is direct sunlight excessive heat dust or vibration Do not store or operate this unit near chem icals or where there are chemical fumes Do not allow an...

Page 2: ...en the disk s usage lifetime A wet bulb temperature of 29 C or less is recommended This is equivalent to the following data Capacity 250GB Average Seek Time 12msec TYP Power Consump tion At Startup 4 5W or less Read Write 1 4W TYP During Wait 0 2W TYP Interface Serial ATA Rev 1 0a Operation Lifetime 5 years or 30 000 operating hours whichever comes first Weight Approx 400g Surrounding Air Temperat...

Page 3: ...3650A 1 Turn OFF the power switch of the PS A and remove the power cable Place the PS A on a flat level surface facing the display face downwards 2 Unscrew the expansion board cover s screws 2 and remove the expansion board cover 3 Unscrew the expansion board base s screws 4 and remove the expansion board base 4 Remove the DISK cover 5 Mount the HDD unit vertically on the circuit board and plug th...

Page 4: ...or damage the HDD unit and PS A 4 Fix the HDD unit with the screws 4 which are contained in your package The torque required to tighten these screws is 0 5 to 0 6 N m 5 With opposite procedure above set the DISK cover to the PS A unit The torque required to tighten these screws is 0 5 to 0 6 N m Digital Electronics Corporation 8 2 52 Nanko higashi Suminoe ku Osaka 559 0031 JAPAN TEL 81 0 6 6613 31...

Reviews: