Service Manual
1-11
General Information
1
Front panel LED service mode error codes
Detected error conditions are displayed on the front panel as LED patterns. The
following table lists the service mode error codes which are displayed while the printer is
in service mode. (Service mode is explained in Chapter 9, “Checks and Adjustments.”)
These codes are more specific than the error codes displayed during normal operation
(see the previous topic “Rear panel). If an error occurs during normal operation, pressing
the rear panel TEST button causes the appropriate, and more specific, service mode error
code to be displayed on the front panel. The error codes listed below are explained in
greater detail in the Chapter 6 topic “Print engine error codes and their causes” on
page 6-19.
o means LED off
Z
means LED on
Z
means the POWER LED which is always on
Table 1-4. Service mode error code summary
Front panel LEDs
Hex codeError
o o o o o
o
Z
00
No error
o o o o o
Z
Z
01
Drum position error.
o o o o
Z
o
Z
02
Thermal head temperature error.
o o o
Z
o
o
Z
04
Top cover open error.
o o o
Z
o
Z
Z
05
Front cover open error.
o o o
Z
Z
o
Z
06
Strobe error.
o o o
Z Z
Z
Z
07
Engine control board RAM error.
o o
Z
o o
o
Z
08
Engine control board ROM error.
o o
Z
o
Z
o
Z
0A
Interface error with image processor board.
o o
Z
Z
o
Z
Z
0D
Thermistor failure.
o o
Z
Z
Z
o
Z
0E
Thermal head lift error.
o o
Z
Z
Z
Z
Z
0F
Thermal head thermistor failure.
o
Z
o o o
o
Z
10
Transfer roll empty.
o
Z
o o o
Z
Z
11
Transfer roll low.
o
Z
o o
Z
Z
Z
12
Transfer roll jam.
o
Z
Z
o o
o
Z
18
Transfer roll feed timer error.
Z
o o o o
o
Z
20
Out of media.
Z
o o o o
Z
Z
21
Tray not installed.
Z
o o o
Z
o
Z
22
Paper eject sensor failed to turn on.
Z
o o o
Z
Z
Z
23
Paper-pass error / lower tray.
Z
o o
Z
o
o
Z
24
Paper-pass error / upper tray.
Z
o o
Z
o
Z
Z
25
Paper-pass sensor 2 error.
Z
o o
Z
Z
o
Z
26
Paper clamped error.
Z
o o
Z
Z
Z
Z
27
Media size error.
Z
o
Z
o o
o
Z
28
Paper eject sensor failed to turn off.
Z
o
Z
o o
Z
Z
29
Paper-pass sensor 1 failed to turn off after
paper eject.
Z
o
Z
o
Z
o
Z
2A
Paper-pass sensor 2 failed to turn off after
paper eject.
Z
o
Z
o
Z
Z
Z
2B
Clamp timer error.
Summary of Contents for DECcolorwriter 1000
