Technical Support
Email:
PN6600@pctreasures.com
Phone: (248) 236-0061, Mon.-Fri., 9:30am-5:30pm
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note 1:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: a) Reorient or relocate the receiving antenna
b) Increase the separation between the equipment and receiver c) Connect the equipment into an outlet on
a circuit different from that to which the receiver is connected d) Consult the dealer or an experienced
radio/TV technician for help.
Note 2:
Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
BEFORE FIRST USE
Your
PowerNow! 6600
comes from the factory with a charge and can be used
right out of the box. However, it is best to make sure that the unit is fully charged
before first use. Press the
Power Button
to see how much charge is in the unit.
The
Battery Status LEDs
light up from left to right to show the charge level. The
Battery Status LEDs
will turn off after a few seconds.
• One LED Lit: 25% Charged
• Two LEDs Lit: 50% Charged
• Three LEDs Lit: 75% Charged • Four LEDs Lit: 100% Charged
Charging the PowerNow! 6600
™
To charge the
PowerNow! 6600
, insert the
Micro USB
end of the included
USB
to Micro USB Charging Cable
into the power bank’s
Micro USB Power Input
Port
and the other end into a
USB Port
on your computer or the included USB
wall adapter. The
Battery Status LEDs
light up to indicate the current power
level. All four lights glow steadily when the unit is fully charged.
Charging a Smartphone, Camera, or Other Device
To charge a smartphone or similar device with the
PowerNow! 6600
, plug the
device into either of the
USB Power Output Ports
and press the
On/Off
Button
. The
Battery Status LEDs
light up, showing the percent of power
remaining in the
PowerNow! 6600
. When the device is fully charged, the
Battery Status LEDs
turn off. You may charge two smartphones (or similar
devices) at one time by plugging one into each
USB Power Output Port
.
25%
Charged
50%
Charged
75%
Charged
100%
Charged
2.1 Amp USB
Power Output Port
On/Off
Button
1.0 Amp USB
Power Output Port
Charging a Tablet
To charge a tablet with the
PowerNow! 6600
, plug the device into the
2.1 Amp USB Power Output Port
and press the
On/Off Button
. The
Battery
Status LEDs
light up, showing the percent of power remaining in the
PowerNow!
6600
. When the device is fully charged, the
Battery Status LEDs
turn off.
IMPORTANT:
If you plug the tablet into the 1.0 Amp USB Power Output
Port, it MAY NOT CHARGE
. The
1.0 Amp USB Power Output Port
does not
provide strong enough power output to charge most tablets.
Using the LED Flashlight
To activate the
LED Flashlight
, press the
On/Off Button
two times. Press the
On/Off Button
two more times to turn the
LED Flashlight
off.
Troubleshooting
The PowerNow! 6600 Will Not Charge
- Check to make sure that the
USB to
Micro USB Charging Cable
is properly connected to the
Micro USB Power In
Port
. If the unit still will not charge, your power cable may be damaged. Connect
the unit using a different power cable.
A Smartphone Will Not Charge
- Check to make sure that the smartphone
is securely connected and the
PowerNow! 6600
is charged. Recharge the
PowerNow! 6600
if necessary. If the smartphone still will not charge, your power
cable may be damaged. Connect the smartphone using a different power cable.
A Tablet Will Not Charge
- Check to make sure that the tablet is securely
connected to the
2.1 Amp USB Power Output Port
. The
1.0 Amp USB Power
Output Port
does not have a strong enough power output to charge a tablet.
Make sure that the
PowerNow! 6600
is charged. Recharge the
PowerNow! 6600
if necessary. If the tablet still will not charge, your power cable may be damaged.
Connect the tablet using a different power cable.
CAUTION:
Store the
PowerNow! 6600
in a cool, dry place. Avoid water and corrosive
chemicals. Do not violently shake or strike. Device contains no user-serviceable
parts. Do not disassemble. If the device is overheating or smoking or if the case
is damaged, deformed, or discolored, immediately discontinue use and contact
the manufacturer.
How to Properly Dispose of Batteries
This product contains lithium-ion batteries. To properly dispose of expired
batteries, view your city’s website or newsletter to find what guidelines, if any,
should be followed and to make note of their hazardous waste collection days.
