The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely con
fi
dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
42
180
Reload every Metre? (if not: every Second)
- Event Counter 4 must be reloaded every metre? If not then it will be reloaded every second. The
allowed answer is either: 0 (No: every second) or: 1 (Yes: every metre).
No / Yes
181
Act. Only Above cross-speed? (if not: Allw.)
- Event Counter 4 should be ac vated only above the cross-speed? If not then it will allways be
ac vated. The allowed answer is either: 0 (No: always) or: 1 (Yes: only above).
No / Yes
182
Event-Counter n.4 is moment. suspended?
- Event Counter number 4 should be momentarily suspended? If not then it will be ac ve.
The allowed answer is either: 0 (No: ac ve) or: 1 (Yes: suspended).
No / Yes
183
At tari
ff
-change discard accumul. Dist/Time?
- If the tari
ff
is changed manually with key K1 should the accumulated distance or me be
discarded?
If not, the accumulated distance or me will be propor onaly accounted for. The allowed answer is either: 0 (No: account for) or: 1 (Yes:
discard).
No / Yes
184
At tari
ff
-change synchronize with next unit?
- If the tari
ff
is changed manually with key K1 should the current unit be completed with the current
parameters? If not, the tari
ff
-change will be immediate. The allowed answer is either: 0 (No: immediate) or: 1 (Yes: synchronize).
No / Yes
185
Extra-Charge n. 4 is a discount?
- Extra-Charge n. 4, as programmed in Q.27, should be interpreted not as an extra-charge but as a discount?
The discount can only be used as a percentage. Therefore the parameter of Q.31 should be programmed as Yes. The allowed answer is either:
0 (No: extra-charge) or: 1 (Yes: discount).
No / Yes
186
In ForHire disable keys K1, K2, K3 and K4?
- In ForHire the keys K1, K2, K3 and K4 should be disabled? In case of Yes the taxi-meter works
normaly including the OP-key but all func ons that can be invoked with the keys K1, K2, K3 and/or K4 are inhibited.
The allowed answer is either:
0 (No: enabled) or: 1 (Yes: disabled).
No / Yes
187
Start-of-Fare me is used for Night/Holiday extras?
- Should the me in which the fare starts be considered for the calcula on of the night
and/or holiday extras? In case of Yes and if there is a change from night/holiday me to normal me (or vice versa) during the trip then for as
long as the trip lasts the fare cost will be calculated as if it is s ll night/holiday me. Star ng from the next fare the parameters for normal me
will be used.
The allowed answer is either:
0 (No) or: 1 (Yes).
No / Yes
188
Show fare and extra-charge divided by 100?
- Should the fare and the extra-charge be shown on their resp. displays divided by 100?
In this way the two least signi
fi
cant digits (usually zero) are not shown. The allowed answer is either: 0 (No: show normal) or: 1 (Yes: show
divided by 100).
No / Yes
189
Available for any possible so ware extension
190
In case Night/Holiday extras are added on Flag drop, have to be added also on Min. trip amount?
No / Yes
191
On Euro conversion apply the Arround func on?
No / Yes
VA RIOUS FUNCTIONS
192
Disable auto-shuto
ff
if car-lights are ON?
- In Stopped with auto-shut-o
ff
disabled the taxi-meter will allways remain ON. In case auto-shut-o
ff
is enabled the taxi-meter will switch OFF automa cally a er the amount of me programmed in Q.284. The allowed answer is either:
0
(No: enabled) or: 1 (Yes: disabled).
No / Yes
193
Enable the light-test?
When this op on is enabled then in case of an error the message ‘ERROR’ ‘LIGHT’ will appear on the display. The light-
test is done on the moment of passing from Stopped to Hired. The lights tested are: TAXI, light 1 to light 4. The allowed answer is either: 0
(No: disabled) or: 1 (Yes: enabled).
No / Yes
194
Block the taxi-meter on light-error?
- At the end of the current fare should the taxi-meter be blocked in case of a light-error?
The allowed answer is either: 0 (No: don’t block) or: 1 (Yes: block).
No / Yes
195
Enable the display-segment-test?
- When this op on is enabled then in case of an error the message ‘ERROR’ ‘DISPL’ will appear on the
display. The display-segment-test is done on the moment of passing from Stopped to Hired. The lights tested are: TAXI and light 1 to light 4.
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
Summary of Contents for M1 mdt
Page 1: ...Technical Manual InstallationandProgramming ver 1 16 12 2014...
Page 2: ......
Page 83: ......
